From: lei zheng (leon_lei@xxxxxxxxxxx)
Date: Mon Aug 20 2001 - 14:01:19 GMT-3
Hi,
The "distribute-sap-list 100* in" command under NLSP can filter the SAP
when you redistribute the IPX EIGRP into NLSP. I think you have no way to
filter SAP when you use NLSP as the single routing protocol in IPX network.
>From: "BRZYSKI, ADAM E (SWBT)" <ab1723@sbc.com>
>Reply-To: "BRZYSKI, ADAM E (SWBT)" <ab1723@sbc.com>
>To: ccielab@groupstudy.com
>Subject: Re: IPX SAP filters and NLSP
>Date: Mon, 20 Aug 2001 09:46:21 -0500
>
>I have encountered the same issue as all of you when I have configured
NLSP.
>
>I have also tried using the distribute-sap-list command under the NLSP
>protocol to try to filter the SAP's out of the NLSP updates with no luck.
>
>Adam Brzyski
>Design Engineer II
>CCNP, CCDP, NNCDE
>
>
>-----Original Message-----
>From: Tony Ng [mailto:tonyng42@usa.net]
>Sent: Monday, August 20, 2001 7:20 AM
>To: Taz Kazam; Jason Sinclair; ccielab@groupstudy.com
>Subject: Re: [Re: IPX SAP filters and NLSP]
>
>
>Taz & Jason,
>
>I have the same problem w/ NLSP (and filtering routes too!). But rip/sap
>compatibility mode is switched to OFF once NLSP is enabled. Do a "show
ipx
>interface ____" and at the very bottom, you will see that the NLSP enabled
>interface is switched OFF for both RIP & SAP. Also, you can validate this
>condition by doing a "debug ipx routing event".
>
>Taz Kazam <taz_kazam@yahoo.co.uk> wrote:
> > Jason,
> >
> > I think I know what the problem might be. NLSP has its
> > own subset of RIP and SAP broadcasts, which need to be
> > switched off.
> >
> > Under the interface where NLSP is running you need to
> > do the following commands:
> >
> > ipx nlsp rip off
> > ipx nlsp sap off
> >
> > I hope this helps!
> >
> > Kind Regards
> > Taz.
> >
> >
> > --- Jason Sinclair <sinclairj@powertel.com.au> wrote:
> > > I have set up a simple two node lab with a 2 static
> > > SAP's on router1
> > > advertised to router2. When I use RIP to advertise
> > > the SAP's, and configure
> > > an inpuut-sap-filter on router2 to block one of the
> > > services it works fine.
> > > However when I use NLSP and stop RIP, the server
> > > re-appears under show ipx
> > > servers. (eg they are both back there). Am I missing
> > > something in NLSP.
> > >
> > > Regards,
> > >
> > > Jason Sinclair
> > > Team Leader - NSG
> > > POWERTEL Limited
> > > Level 11, 55 Clarence Street, SYDNEY
> > > Phone: 61-2-8264-3820
> > > Mobile: 0416 105 858
> > > jasons@powertel.net.au
> > >
> > >
> > >
> > >
> > >
> > **********************************************************************
> > > This email (including all attachments) is intended
> > > solely for the named
> > > addressee. It is confidential and may contain
> > > commercially sensitive
> > > information. If you receive it in error, please let
> > > us know by reply email,
> > > delete it from your system and destroy any copies.
> > >
> > > This email is also subject to copyright. No part of
> > > it should be reproduced,
> > > adapted or transmitted without the prior written
> > > consent of the copyright owner.
> > >
> > > Emails may be interfered with, may contain computer
> > > viruses or other defects
> > > and may not be successfully replicated on other
> > > systems. We give no
> > > warranties in relation to these matters. If you have
> > > any doubts about
> > > the authenticity of an email purportedly sent by us,
> > > please contact us
> > > immediately.
> > >
> > >
> > **********************************************************************
> > > **Please
> > > read:http://www.groupstudy.com/list/posting.html
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:31:54 GMT-3