From: BRZYSKI, ADAM E (SWBT) (ab1723@xxxxxxx)
Date: Mon Aug 20 2001 - 11:46:21 GMT-3
I have encountered the same issue as all of you when I have configured NLSP.
I have also tried using the distribute-sap-list command under the NLSP
protocol to try to filter the SAP's out of the NLSP updates with no luck.
Adam Brzyski
Design Engineer II
CCNP, CCDP, NNCDE
-----Original Message-----
From: Tony Ng [mailto:tonyng42@usa.net]
Sent: Monday, August 20, 2001 7:20 AM
To: Taz Kazam; Jason Sinclair; ccielab@groupstudy.com
Subject: Re: [Re: IPX SAP filters and NLSP]
Taz & Jason,
I have the same problem w/ NLSP (and filtering routes too!). But rip/sap
compatibility mode is switched to OFF once NLSP is enabled. Do a "show ipx
interface ____" and at the very bottom, you will see that the NLSP enabled
interface is switched OFF for both RIP & SAP. Also, you can validate this
condition by doing a "debug ipx routing event".
Taz Kazam <taz_kazam@yahoo.co.uk> wrote:
> Jason,
>
> I think I know what the problem might be. NLSP has its
> own subset of RIP and SAP broadcasts, which need to be
> switched off.
>
> Under the interface where NLSP is running you need to
> do the following commands:
>
> ipx nlsp rip off
> ipx nlsp sap off
>
> I hope this helps!
>
> Kind Regards
> Taz.
>
>
> --- Jason Sinclair <sinclairj@powertel.com.au> wrote:
> > I have set up a simple two node lab with a 2 static
> > SAP's on router1
> > advertised to router2. When I use RIP to advertise
> > the SAP's, and configure
> > an inpuut-sap-filter on router2 to block one of the
> > services it works fine.
> > However when I use NLSP and stop RIP, the server
> > re-appears under show ipx
> > servers. (eg they are both back there). Am I missing
> > something in NLSP.
> >
> > Regards,
> >
> > Jason Sinclair
> > Team Leader - NSG
> > POWERTEL Limited
> > Level 11, 55 Clarence Street, SYDNEY
> > Phone: 61-2-8264-3820
> > Mobile: 0416 105 858
> > jasons@powertel.net.au
> >
> >
> >
> >
> >
> **********************************************************************
> > This email (including all attachments) is intended
> > solely for the named
> > addressee. It is confidential and may contain
> > commercially sensitive
> > information. If you receive it in error, please let
> > us know by reply email,
> > delete it from your system and destroy any copies.
> >
> > This email is also subject to copyright. No part of
> > it should be reproduced,
> > adapted or transmitted without the prior written
> > consent of the copyright owner.
> >
> > Emails may be interfered with, may contain computer
> > viruses or other defects
> > and may not be successfully replicated on other
> > systems. We give no
> > warranties in relation to these matters. If you have
> > any doubts about
> > the authenticity of an email purportedly sent by us,
> > please contact us
> > immediately.
> >
> >
> **********************************************************************
> > **Please
> > read:http://www.groupstudy.com/list/posting.html
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:31:54 GMT-3