From: Andrew Lennon (andrew.lennon@xxxxxxxxxxxxx)
Date: Sun May 20 2001 - 08:58:39 GMT-3
Hi all
Here is the config from my ts. This works fine and I dont get any errors
with lines needing to be cleared....
I have posted the whole config. Please ignore the non relevant parts.
Andy
Password:
termsvr>en
Password:
termsvr#sh run
Building configuration...
Current configuration : 2831 bytes
!
! No configuration change since last restart
!
version 12.1
no service single-slot-reload-enable
service timestamps debug datetime localtime show-timezone
service timestamps log datetime localtime show-timezone
no service password-encryption
service udp-small-servers
service tcp-small-servers
!
hostname termsvr
!
logging rate-limit console 10 except errors
enable password cisco
!
username admin password 0 admin
clock timezone GMT 0
clock summer-time BST recurring last Sun Mar 1:00 last Sun Oct 1:00
ip subnet-zero
no ip finger
ip domain-name lennon.nscglobal.com
ip host r2504a 2014 172.16.0.1
ip host r4700 2009 172.16.0.1
ip host r1601 2010 172.16.0.1
ip host r2511b 2011 172.16.0.1
ip host r2503b 2013 172.16.0.1
ip host r2504b 2015 172.16.0.1
ip host bay 2016 172.16.0.1
ip host r2503a 2012 172.16.0.1
ip name-server 192.168.6.252
!
ipx routing 0060.5cf3.fcf7
ipx maximum-hops 20
cns event-service server
!
!
!
!
!
interface Loopback0
ip address 172.16.0.1 255.255.255.255
!
interface Ethernet0
ip address 192.168.6.244 255.255.255.0
load-interval 30
!
interface Ethernet0.4
ipx encapsulation SNAP
ipx network BADBAD1
!
interface Serial0
bandwidth 2000
ip address 172.16.1.1 255.255.255.240
encapsulation frame-relay
ip ospf network point-to-multipoint
no ip mroute-cache
ipx network CC1E
cdp enable
frame-relay map ip 172.16.1.3 503 broadcast
frame-relay map ip 172.16.1.4 503 broadcast
frame-relay map ipx CC1E.0003.0003.0003 703 broadcast
frame-relay map ipx CC1E.0004.0004.0004 703 broadcast
no frame-relay inverse-arp
!
interface Serial1
bandwidth 2000
ip address 172.16.13.1 255.255.255.0
ip router isis
!
router ospf 1
log-adjacency-changes
area 1 range 172.16.1.0 255.255.255.0
summary-address 172.16.1.0 255.255.255.0
redistribute isis level-2 metric 90 subnets
redistribute igrp 1 metric 50 subnets
network 172.16.0.1 0.0.0.0 area 1
network 172.16.1.0 0.0.0.15 area 1
network 192.168.6.0 0.0.0.255 area 1
default-information originate metric 100
!
router isis
redistribute ospf 1 metric 20
distance 50 ip
net 49.0001.0000.0000.0001.00
!
ip kerberos source-interface any
ip classless
ip default-network 192.168.6.0
ip route 0.0.0.0 0.0.0.0 192.168.6.254
no ip http server
!
!
!
!
ipx router eigrp 1
network CC1E
!
!
ipx router rip
no network CC1E
!
!
ipx sap 8 ccie8 BADBAD.0000.0000.0001 451 2
!
!
line con 0
exec-timeout 0 0
transport input none
line 1 16
no exec
transport input all
line aux 0
no exec
transport input all
line vty 0 4
exec-timeout 3000 0
password cisco
login
!
ntp authentication-key 1 md5 070C285F4D06 7
ntp authenticate
ntp clock-period 17179915
ntp source Loopback0
ntp server 158.152.1.76 prefer
end
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Jeongwoo Park
Sent: 20 May 2001 10:40
To: Yongchul Yang; Ccielab@Groupstudy. Com
Subject: RE: Terminal Server for the first time !!! [7:5119]
Hi all
I made some changes on config.
Still didn't work.
Here is new config:
TermServer#sh run
Building configuration...
Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname TermServer
!
enable password wams
!
ip subnet-zero
no ip domain-lookup
ip host r1 2001 1.1.1.1
ip host r2 2002 1.1.1.1
ip host r3 2003 1.1.1.1
!
!
!
interface Loopback0
ip address 1.1.1.1 255.255.255.255
no ip directed-broadcast
!
interface Ethernet0
no ip address
no ip directed-broadcast
shutdown
!
interface Serial0
ip address 5.5.5.5 255.255.255.0
no ip directed-broadcast
no ip mroute-cache
no fair-queue
clockrate 64000
!
interface Serial1
ip address 5.5.6.5 255.255.255.0
no ip directed-broadcast
!
ip classless
!
!
line con 0
no exec
transport input none
line 1 8
transport input all
transport output none
stopbits 1
line aux 0
line vty 0 4
login
!
end
Now I did "sh line"
TermServer#sh line
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 CTY - - - - - 15 0 0/0 -
* 1 TTY 9600/9600 - - - - - 7 20 4/17 -
* 2 TTY 9600/9600 - - - - - 7 0 0/0 -
3 TTY 9600/9600 - - - - - 1 0 0/0 -
4 TTY 9600/9600 - - - - - 0 0 0/0 -
5 TTY 9600/9600 - - - - - 0 323 179/539 -
6 TTY 9600/9600 - - - - - 0 0 0/0 -
7 TTY 9600/9600 - - - - - 0 15 119/356 -
* 8 TTY 9600/9600 - - - - - 0 22 21/63 -
9 AUX 9600/9600 - - - - - 0 0 0/0 -
10 VTY - - - - - 0 0 0/0 -
11 VTY - - - - - 0 0 0/0 -
12 VTY - - - - - 0 0 0/0 -
13 VTY - - - - - 0 0 0/0 -
14 VTY - - - - - 0 0 0/0 -
Then I did this
TermServer#clear line 1
[confirm]
[OK]
TermServer#clear line 2
[confirm]
[OK]
TermServer#clear line 8
[confirm]
[OK]
TermServer#sh line
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 CTY - - - - - 15 0 0/0 -
1 TTY 9600/9600 - - - - - 7 90 7/26 -
2 TTY 9600/9600 - - - - - 7 0 0/0 -
3 TTY 9600/9600 - - - - - 1 0 0/0 -
4 TTY 9600/9600 - - - - - 0 0 0/0 -
5 TTY 9600/9600 - - - - - 0 323 179/539 -
6 TTY 9600/9600 - - - - - 0 0 0/0 -
7 TTY 9600/9600 - - - - - 0 15 119/356 -
* 8 TTY 9600/9600 - - - - - 0 22 21/63 -
9 AUX 9600/9600 - - - - - 0 0 0/0 -
10 VTY - - - - - 0 0 0/0 -
11 VTY - - - - - 0 0 0/0 -
12 VTY - - - - - 0 0 0/0 -
13 VTY - - - - - 0 0 0/0 -
14 VTY - - - - - 0 0 0/0 -
Now it shows this:
TermServer#sh line
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 CTY - - - - - 15 0 0/0 -
1 TTY 9600/9600 - - - - - 7 90 7/26 -
2 TTY 9600/9600 - - - - - 7 0 0/0 -
3 TTY 9600/9600 - - - - - 1 0 0/0 -
4 TTY 9600/9600 - - - - - 0 0 0/0 -
5 TTY 9600/9600 - - - - - 0 323 179/539 -
6 TTY 9600/9600 - - - - - 0 0 0/0 -
7 TTY 9600/9600 - - - - - 0 15 119/356 -
* 8 TTY 9600/9600 - - - - - 0 22 21/63 -
9 AUX 9600/9600 - - - - - 0 0 0/0 -
10 VTY - - - - - 0 0 0/0 -
11 VTY - - - - - 0 0 0/0 -
12 VTY - - - - - 0 0 0/0 -
13 VTY - - - - - 0 0 0/0 -
14 VTY - - - - - 0 0 0/0 -
At this point, I am confused because line 8 was not cleared.
Now I typed "r1" This is what it looks like:
TermServer#r1
Trying r1 (1.1.1.1, 2001)... Open
And I get stuck forever.
I had to go (ctrl+shift+6)+X to go back to TermServer prompt.
At TermServer prompt, I did "sh line" again.
TermServer#sh line
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 CTY - - - - - 16 0 0/0 -
* 1 TTY 9600/9600 - - - - - 8 90 7/26 -
2 TTY 9600/9600 - - - - - 7 0 0/0 -
3 TTY 9600/9600 - - - - - 1 0 0/0 -
4 TTY 9600/9600 - - - - - 0 0 0/0 -
5 TTY 9600/9600 - - - - - 0 323 179/539 -
6 TTY 9600/9600 - - - - - 0 0 0/0 -
7 TTY 9600/9600 - - - - - 0 15 119/356 -
* 8 TTY 9600/9600 - - - - - 0 22 21/63 -
9 AUX 9600/9600 - - - - - 0 0 0/0 -
10 VTY - - - - - 0 0 0/0 -
11 VTY - - - - - 0 0 0/0 -
12 VTY - - - - - 0 0 0/0 -
13 VTY - - - - - 0 0 0/0 -
14 VTY - - - - - 0 0 0/0 -
So I cleared line 1 by doing this "clear line 1"
And typed r1. It still showed this shit.
TermServer#r1
Trying r1 (1.1.1.1, 2001)... Open
I just made longer message than I intended to. But since I am struggling to
get this to work, I want to try every possible way.
I hope I showed you better.
Any input would be appreciated
Thanks.
Jeongwoo
-----Original Message-----
From: Yongchul Yang [mailto:whycwhy@socal.rr.com]
Sent: Sunday, May 20, 2001 12:09 AM
To: Jeongwoo Park
Subject: RE: Terminal Server for the first time !!! [7:5119]
Jeongwoo,
Don't let other sample configuration confuse you, your configuration is
absolutely correct. It just takes a few practice sessions to get
comfortable using the terminal server. A lot of people make simple mistakes
on how to use it. Just simply press 2nd 'enter' key after typing r1 &
enter. If the session is refused by any reason, just check the line status
with either 'show session' or 'show line' command. If you are using 2509
with rj45 asynch interface make sure you are using the rolled cable, if you
are using the octal cable, they are already rolled. Another scenario is
using the rj45 patch panel, if you have octal or rolled rj45 cable connected
to the patch panel, make sure you are using the straight cable between your
routers' console ports.
Once you have the physical set up of using the terminal server, keep
practice using it on all you lab exam practice, then you will start
developing some short cuts of your own. I don't particularly like using the
terminal server because I can only monitor one router at a time, but that's
what you are going to have at your lab exam.
Good luck,
Yongchul Yang
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Jeongwoo Park
Sent: Saturday, May 19, 2001 7:34 AM
To: cisco@groupstudy.com
Subject: Terminal Server for the first time !!! [7:5119]
Hi all
How can I get my 2509 terminal server to work?
Here is my config
TermServer#sh r
05:47:29: %SYS-5-CONFIG_I: Configured from console by consoleun
Building configuration...
Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname TermServer
!
enable password wams
!
ip subnet-zero
no ip domain-lookup
ip host r1 2001 1.1.1.1
ip host r2 2002 1.1.1.1
ip host r3 2003 1.1.1.1
!
!
!
interface Loopback0
ip address 1.1.1.1 255.255.255.255
no ip directed-broadcast
!
interface Ethernet0
no ip address
no ip directed-broadcast
shutdown
!
interface Serial0
ip address 2.2.50.2 255.255.255.252
no ip directed-broadcast
no ip mroute-cache
no fair-queue
clockrate 64000
shutdown
!
interface Serial1
ip address 3.3.50.1 255.255.255.252
no ip directed-broadcast
clockrate 1300000
shutdown
!
ip classless
!
!
line con 0
line 1 8
no exec
transport input all
line aux 0
line vty 0 4
login
!
end
I have three other router that are r1, r2, and r3 respectively.
How can I get to r1, r2, or r3?
Isn't it this one? for example,
TermServer#r1
TermServer#r2
TermServer#r3
It did not work
I am using termserver for the first time.
Can someone guide me through how to use it?
In addition, here is output of "sh line"
TermServer#sh line
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 CTY - - - - - 6 1 0/0 -
* 1 TTY 9600/9600 - - - - - 3 2 0/0 -
* 2 TTY 9600/9600 - - - - - 2 0 0/0 -
3 TTY 9600/9600 - - - - - 1 0 0/0 -
4 TTY 9600/9600 - - - - - 0 0 0/0 -
5 TTY 9600/9600 - - - - - 0 104 0/0 -
6 TTY 9600/9600 - - - - - 0 0 0/0 -
7 TTY 9600/9600 - - - - - 1 0 81/243 -
8 TTY 9600/9600 - - - - - 0 6 208/622 -
9 AUX 9600/9600 - - - - - 0 0 0/0 -
10 VTY - - - - - 1 0 0/0 -
11 VTY - - - - - 0 0 0/0 -
12 VTY - - - - - 0 0 0/0 -
13 VTY - - - - - 0 0 0/0 -
14 VTY - - - - - 0 0 0/0 -
Thanks
jp
FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to abuse@groupstudy.com
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:30:46 GMT-3