From: Kevin Mahler (kemahler@xxxxxxxxx)
Date: Thu May 03 2001 - 09:12:55 GMT-3
Steve,
Don't get confused. You are doing it right. It's a reverse Telnet through
the 2511. I assume you have hit return a few times after establishing the
connection. Here is the config from my 2511. Hope it helps.
Kevin
Current configuration:
!
! Last configuration change at 17:00:51 EDT Wed May 2 2001
!
version 11.2
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
no service udp-small-servers
no service tcp-small-servers
!
hostname TermSrv
!
enable secret 5 $$$$$$$$$$$$$$$$$$$$$$$
!
no ip domain-lookup
ip host r5 2005 1.1.1.1
ip host r4 2004 1.1.1.1
ip host cat5k 2009 1.1.1.1
ip host r7 2007 1.1.1.1
ip host r6 2006 1.1.1.1
ip host r8 2008 1.1.1.1
ip host gw 2014 1.1.1.1
ip host r2 2002 1.1.1.1
ip host r3 2003 1.1.1.1
ip host r1 2001 1.1.1.1
ip host netopai 2009 1.1.1.1
ip host cat2900 2015 1.1.1.1
ip host pix 2013 1.1.1.1
ip host frs 2010 1.1.1.1
ipx routing 0000.0c75.9d72
clock timezone EST -5
clock summer-time EDT recurring
!
interface Loopback0
ip address 1.1.1.1 255.255.255.0
!
interface Ethernet0
ip address Ip address removed 255.255.255.224
!
interface Serial0
no ip address
shutdown
no fair-queue
!
interface Serial1
no ip address
shutdown
!
ip classless
ip route 0.0.0.0 0.0.0.0 IP address removed.
ip http server
!
!
!
!
alias exec c config t
alias exec s show running config
alias exec save write mem
alias exec ship show ip route
alias exec shin show ip int brie
alias exec shix show ipx route
alias exec shixn show ipx int brie
alias exec shap show apple route
alias exec shaz show apple zone
alias exec shib show ip bgp
alias exec shibs show ip bgp summ
!
line con 0
line 1 16
no exec
transport input all
line aux 0
line vty 0 4
exec-timeout 0 0
password 7 $$$$$$$$$$$$$$$$
login
!
ntp authentication-key 1 md5 $$$$$$$$$$$ 7
end
TermSrv#
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
louie kouncar
Sent: Wednesday, May 02, 2001 11:32 PM
To: 'Steve Grewal'; ccielab@groupstudy.com
Subject: RE: Cisco 2511 Terminal Server
Steve,
The whole point of having a terminal server is not to telnet to your
routers, all you have to do is connect an octopus cable from your ASYNC
ports on the 2511 to the console port of your other routers, then you need
to configure the terminal server with an ip address, I would use a lo
interface address such as 1.1.1.1 and then here is the command you need:
ip host "Name of router" 2001 1.1.1.1
in this example you have a router ,which you can give a name, connected to
your first console cable labled 1 of your octopus cable which is connected
to ASYNC port 1-8.
to access your routers all you need to do is type the name you give it, if
you gave the first router a name of R1, then type R1 at the prompt of your
terminal server and you should be good to go, to get back to the TS use
CTRL+SHIFT+6 X.
Hope that helps......
Louie J. Kouncar
TCO3 Senior Data Center Engineer
UUNET
W-703-343-6645
C-703-304-2460
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Steve Grewal
Sent: Wednesday, May 02, 2001 10:53 PM
To: ccielab@groupstudy.com
Subject: Cisco 2511 Terminal Server
Hello All,
Recently purchased a home lab in efforts to prepare for my CCIE lab, having
some issues configuring my terminal server! I have verified my config (on
my terminal server as well as my remote router) but the message i get is as
follows when i try to connect from my terminal server to the remote router:
TerminalServer>telnet Router1 2001
Trying Router1 (172.21.1.1, 2001)... Open
It seems as though the session is being established but I am not getting any
type of display! I would really appreciate if someone could point me to the
right direction for any available papers on this issue or possibly give me
the solution!
Thanks in advance!
Regards,
Steve Grewal
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:30:33 GMT-3