RE: DLSW: How do generate DLSW traffic from routers.

From: Glen Lavers (glavers@xxxxxxxxx)
Date: Fri Apr 20 2001 - 03:53:37 GMT-3

   
Hi Elias,
Send your configs and I'll have a look. My lab's tomorrow so I haven't been
spending too much time checking my emails if you know what I mean.
Cheers,
Glen

-----Original Message-----
From: Elias Aggelidis [mailto:eaggel@algo.com.gr]
Sent: Friday, April 20, 2001 12:38 AM
To: Glen Lavers; Devender Singh; Ccielab@Groupstudy. Com (E-mail)
Subject: RE: DLSW: How do generate DLSW traffic from routers.

Dear Glen

I am trying to implement what you have proposed
But no lack !!!!!

DSPU HOST TESTDLSW is trying again and again but the other end
does not send a bit.

Any hinds ?

Regards

****************************************************************
Elias Aggelidis ALGOSYSTEMS SA
Senior Network Engineer 4, Sardeon Str
CCNA, CCNP Nea Smyrni
CVOICE, Security Specialised
PICA Administrator
                                                  Athens 17121
tel: +301-9310281 GREECE
fax: +301-9352873
email: eaggel@algo.com.gr
****************************************************************

-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of Glen
Lavers
Sent: ??5pt?, 19 ?p?????? 2001 12:30 55
To: Devender Singh; Ccielab@Groupstudy. Com (E-mail)
Subject: RE: DLSW: How do generate DLSW traffic from routers.

I think this is what you might be after.
Glen

<<---
R1(HOST)--t/r--R2--DLSw--R3--t/r--R4(PU)

In the above topology R2 and R3 are dlsw peers.
R4 is trying to connect to R1 using LLC2 as
as its transport for SNA..

You can replace the tokenrings with ethernets,
and leave the below config untouched

If you change only one side do not forget the bitswapping :
http://www-tac.cisco.com/TOOLS/Applications/bitswap.html

Sending Router (emulating SNA PU) -> R4
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
dspu host TESTDLSW xid-snd 01712345 rmac 4000.3745.0001 rsap 4 lsap 4

interface TokenRing0
dspu enable-host lsap 4
dspu start TESTDLSW
end

Receiving Router (emulating Mainframe) -> R1
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
dspu pu HOST xid-rcv 01712345

interface TokenRing0
mac-address 4000.3745.0001
dspu enable-pu lsap 4

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Commands to use :

show dlsw peer
show dlsw reach
show dlsw circuit detail
show llc
show rif
show source
debug dlsw core
debug token ring

*****************************************************************

-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Devender Singh
Sent: Wednesday, April 18, 2001 10:34 AM
To: Ccielab@Groupstudy. Com (E-mail)
Subject: DLSW: How do generate DLSW traffic from routers.

Can someone guide me how to generate DLSW traffic, so that can do some real
work on dlsw.

thanks in advance.

Devender Singh
BE(Hons), CCNP
IP Solution Specialist
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html

This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:29:52 GMT-3