From: Hale, Wendy (WRHale@xxxxxxxxxx)
Date: Fri Apr 20 2001 - 01:30:14 GMT-3
I erased the config's on my routers, reset the Teltone to factory defaults,
retyped my configs and Voila! it now works. Go figure.
Thanks to everyone for their comments.
-----Original Message-----
From: Clifton Stewart [mailto:cliftonlstewart@home.com]
Sent: Thursday, April 19, 2001 3:14 PM
To: Price, Jamie; ccielab@groupstudy.com
Subject: Problems with Teltone/2500's
I have a Teltone Demonstrator and it supports multiple switch types. You
need to
upgrade the software on the box. I agree with Z, try a basic config to see
if
the problem still exists.
-Cliff
"Price, Jamie" wrote:
> As far as I know - I'm sure someone will correct me if I'm wrong :) - the
> demonstrator ONLY supports 1 switch type - NI1. The Teltone "Simulator"
> supports multiple switch types.
>
> Jamie
>
> -----Original Message-----
> From: chris@pacinter.net [mailto:chris@pacinter.net]
> Sent: Thursday, April 19, 2001 3:15 PM
> To: Hale, Wendy; ccielab@groupstudy.com
> Subject: Re: Problems with Teltone/2500's
>
> Wendy:
> Usually the ISDN switch type is Basic-NI or 5ess. Depending
on
> your telco. I know Sprint / Att usually use basic-ni
>
> The config parameters on your Teltone should be B8ZS.for signalling.not
sure
> about yor other config options Define your default route to be on the
> interface and not the network, that way the interface will dial out
> immediately. Although it sounds like your delay is caused from the network
> and not the DTE device..
>
> Hope this helps!
>
> Chris Martin
>
> ----- Original Message -----
> From: "Hale, Wendy" <WRHale@NECBNS.com>
> To: <ccielab@groupstudy.com>
> Sent: Thursday, April 19, 2001 12:52 PM
> Subject: Problems with Teltone/2500's
>
> > I have a Teltone Demonstrator connected to a 2503 and 2520 via Adtran
ACE1
> > NT's. I get multiple-frame-established and valid spid's. When I enable
> > debug isdn q921/q931 and generate interesting traffic, I get an error
> > message saying that there was a delayed response from the called number.
> > This happens dialing from either router. IOS 12.1(9)
> >
> > 1. Have anyone seen this problem before?
> >
> > 2. Does anyone know what config parameters I should use on the Teltone
> and
> > which isdn switch type on the routers?
> >
> > Thanks!
> >
> > Wendy Hale
> > NEC/BNS
> > 818-599-7698 mobile
> > 877-445-8834 pager
> > 818-672-2438 office
> > WRHale@necbns.com
> > **Please read:http://www.groupstudy.com/list/posting.html
> **Please read:http://www.groupstudy.com/list/posting.html
> **Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:29:52 GMT-3