From: Andrew White (AWHITE@xxxxxxxxxxx)
Date: Thu Apr 19 2001 - 21:04:24 GMT-3
R7-FRYSWITCH)(config)#int s1/3
R7-FRYSWITCH)(config-if)#frame-relay route 100 interface ?
Serial Serial
Tunnel Tunnel interface
IOS:
flash:c2600-ajs-mz_120-9.bin" enterprise ...
This allows frame-relay switching over a tunnel, see below:
http://www.alliancedatacom.com/cisco-frame-relay-configuration.htm
cheers
Andrew
-----Original Message-----
From: Elias Aggelidis [mailto:eaggel@algo.com.gr]
Sent: Friday, 20 April, 2001 11:40
To: Padhu (LFG); 'Johnny Dedon'; Carl Phelan; ccielab@groupstudy.com
Subject: RE: Frame Relay Switch with 2 Routers
I have found the problem that Carl is saying .
In 12.0 this command is not supported any more ...
I am using T version and I can not find it.
Although in 11.0 is supported !!!!!
regards
****************************************************************
Elias Aggelidis ALGOSYSTEMS SA
Senior Network Engineer 4, Sardeon Str
CCNA, CCNP Nea Smyrni
CVOICE, Security Specialised
PICA Administrator
Athens 17121
tel: +301-9310281 GREECE
fax: +301-9352873
email: eaggel@algo.com.gr
****************************************************************
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of Padhu
(LFG)
Sent: ?a?as?e??, 20 ?p?????? 2001 2:07 p5
To: 'Johnny Dedon'; Carl Phelan; ccielab@groupstudy.com
Subject: RE: Frame Relay Switch with 2 Routers
Yes,
You can do frame-relay switching over tunnel interfaces...The only thing to
watch out is the DLCI's are mapped currently in the frame routes...For the
sake of simplicity use the same
numbers all over and it should work.
Cheers,Padhu
-----Original Message-----
From: Johnny Dedon [mailto:johnny.dedon@exodus.net]
Sent: Thursday, April 19, 2001 5:55 PM
To: Carl Phelan; ccielab@groupstudy.com
Subject: Re: Frame Relay Switch with 2 Routers
Carl,
I haven't read this document but I don't think there is a way to do
frame-relay switching over anything but a serial connection.
Johnny
----- Original Message -----
From: "Carl Phelan" <carlphelan@hotmail.com>
To: <ccielab@groupstudy.com>
Sent: Thursday, April 19, 2001 5:40 PM
Subject: Frame Relay Switch with 2 Routers
> Hi,
>
> I am following the document from CCprep to create a frame relay switch
from
> two 2501s. When I come to enter the following command:
> 'frame-relay route 501 interface t0 105'
> in interface mode on Serial 1, the router reports an error in the command
> syntax with 't' or even the full word 'tunnel'. When I replace 't0' with
a ?
> the response is that it only expects the word 'serial'.
> I have tried IOS ver 11.1, 11.2 and 12.0 with the same problem on
different
> routers - anybody have any ideas?
>
> Thanks.
> **Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:29:52 GMT-3