From: David Anderson (dma@xxxxxxxxx)
Date: Tue Feb 27 2001 - 15:39:30 GMT-3
Have you tried to format the flash card and then load a new IOS image onto
it? Try that and see if it helps.
David
At 03:03 PM 2/27/2001 -0800, Norberto Padin wrote:
>This error is when you use a flash that is not supported by the router.
>Not all the PCMCIA flash brands are valid.
>
>
>My 2 cents.
>Nor.
>
>-----Original Message-----
>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
>MASK
>Sent: Tuesday, February 27, 2001 9:33 AM
>To: Richard Gallagher; ccielab@groupstudy.com
>Subject: Re: Problem with 3640
>
>
>hi,
>
>i've tried loading IOS via slot0: but it gives this
>error.
>
>rommon 6 > boot slot0:c3640-is-mz.120-4.T.bin..bin
>device does not contain a valid magic number
>loadprog: error - on file open
>boot: cannot load "slot0:c3640-i"-mz.120-4.T.bin..bin
>rommon 7 >
>
>i think, only hope is now loading CON port.
>i'm gonna try it now.
>Thx
>--- Richard Gallagher <rgallagh@cisco.com> wrote:
> > It look like it is still trying to boot from the
> > internal flash even though you
> > may have a valid image in slot0:
> >
> > So try to enter the following command at rommon when
> > a valid image is in slot0:
> >
> > boot slot0:filename
> >
> > otherwise you may have to do a xmoden transfer of
> > the IOS to the internal
> > flash.
> >
> > Rich
> >
> > On Feb 27, 4:51pm, MASK chatted about:
> > > Subject:Problem with 3640
> > > hi guys,
> > >
> > > My 3640 router, which was functioning like champ
> > till
> > > yesterday, is now, going continuously into ROMMON
> > > mode, i dunno what the heck with it, following is
> > the
> > > error output from 3640 console.
> > > ===============
> > > System Bootstrap, Version 11.1(20)AA2, EARLY
> > > DEPLOYMENT RELEASE SOFTWARE (fc1)
> > > C3600 processor with 32768 Kbytes of main memory
> > > Main memory is configured to 64 bit mode with
> > parity
> > > disabled
> > >
> > > loadprog: bad file magic number: 0x0
> > > boot: cannot load "flash:"
> > > ===============
> > > and i've tried putting a valid 3640 image in
> > > slot0:/slot1:, but it gives the same error message
> > > with slot0:/slot1: mentioned.
> > >
> > > i.e.,
> > > ================
> > >
> > > System Bootstrap, Version 11.1(20)AA2, EARLY
> > > DEPLOYMENT RELEASE SOFTWARE (fc1)
> > > C3600 processor with 32768 Kbytes of main memory
> > > Main memory is configured to 64 bit mode with
> > parity
> > > disabled
> > >
> > > device does not contain a valid magic number
> > > boot: cannot open "slot0:"
> > > boot: cannot determine first file name on device
> > > "slot0:"
> > > =================
> > >
> > > Someone plz help me out!!!!
> > >
> > > Thx
> > >
> > >
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:29:08 GMT-3