From: MASK (afaqk@xxxxxxxxxxxxxx)
Date: Tue Feb 27 2001 - 16:19:17 GMT-3
hi,
i've done transfer via CON port, and the router is
back to normal...Thanks GOD....
For all those who want to transfer via console port in
hyper terminal, always remember to wait for the
"Download Complete!" message on the console, and if
hyperterm seems to stuck just after the file transfer
via xmodem, then close it, and run it again, but NEVER
reload the router....
Thx
--- David Anderson <dma@cisco.com> wrote:
> Have you tried to format the flash card and then
> load a new IOS image onto
> it? Try that and see if it helps.
> David
>
> At 03:03 PM 2/27/2001 -0800, Norberto Padin wrote:
> >This error is when you use a flash that is not
> supported by the router.
> >Not all the PCMCIA flash brands are valid.
> >
> >
> >My 2 cents.
> >Nor.
> >
> >-----Original Message-----
> >From: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com]On Behalf Of
> >MASK
> >Sent: Tuesday, February 27, 2001 9:33 AM
> >To: Richard Gallagher; ccielab@groupstudy.com
> >Subject: Re: Problem with 3640
> >
> >
> >hi,
> >
> >i've tried loading IOS via slot0: but it gives this
> >error.
> >
> >rommon 6 > boot slot0:c3640-is-mz.120-4.T.bin..bin
> >device does not contain a valid magic number
> >loadprog: error - on file open
> >boot: cannot load
> "slot0:c3640-i"-mz.120-4.T.bin..bin
> >rommon 7 >
> >
> >i think, only hope is now loading CON port.
> >i'm gonna try it now.
> >Thx
> >--- Richard Gallagher <rgallagh@cisco.com> wrote:
> > > It look like it is still trying to boot from the
> > > internal flash even though you
> > > may have a valid image in slot0:
> > >
> > > So try to enter the following command at rommon
> when
> > > a valid image is in slot0:
> > >
> > > boot slot0:filename
> > >
> > > otherwise you may have to do a xmoden transfer
> of
> > > the IOS to the internal
> > > flash.
> > >
> > > Rich
> > >
> > > On Feb 27, 4:51pm, MASK chatted about:
> > > > Subject:Problem with 3640
> > > > hi guys,
> > > >
> > > > My 3640 router, which was functioning like
> champ
> > > till
> > > > yesterday, is now, going continuously into
> ROMMON
> > > > mode, i dunno what the heck with it, following
> is
> > > the
> > > > error output from 3640 console.
> > > > ===============
> > > > System Bootstrap, Version 11.1(20)AA2, EARLY
> > > > DEPLOYMENT RELEASE SOFTWARE (fc1)
> > > > C3600 processor with 32768 Kbytes of main
> memory
> > > > Main memory is configured to 64 bit mode with
> > > parity
> > > > disabled
> > > >
> > > > loadprog: bad file magic number: 0x0
> > > > boot: cannot load "flash:"
> > > > ===============
> > > > and i've tried putting a valid 3640 image in
> > > > slot0:/slot1:, but it gives the same error
> message
> > > > with slot0:/slot1: mentioned.
> > > >
> > > > i.e.,
> > > > ================
> > > >
> > > > System Bootstrap, Version 11.1(20)AA2, EARLY
> > > > DEPLOYMENT RELEASE SOFTWARE (fc1)
> > > > C3600 processor with 32768 Kbytes of main
> memory
> > > > Main memory is configured to 64 bit mode with
> > > parity
> > > > disabled
> > > >
> > > > device does not contain a valid magic number
> > > > boot: cannot open "slot0:"
> > > > boot: cannot determine first file name on
> device
> > > > "slot0:"
> > > > =================
> > > >
> > > > Someone plz help me out!!!!
> > > >
> > > > Thx
> > > >
> > > >
> > > >
> > > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:29:08 GMT-3