From: Dan (dp595@xxxxxxxxxxxxx)
Date: Sat Feb 17 2001 - 18:41:26 GMT-3
Actually I would like to correct myself. I really can't say that Erick's
solution is much better in most cases. It just really depends. You need to
know how to do it both ways and you need to be able to determine when which
method is more appropriate.
In your case adding the "network x.x.x.x" statement under the IGRP process
is probably the best way to go, although I'd have to see your config and
requirements/desired results before saying for sure.
Dan Pontrelli
Customer Installation Engineer - Verio NYC
CCNP, MCSE, CNA
----- Original Message -----
From: "Dan" <dp595@optonline.net>
To: "Erick B." <erickbe@yahoo.com>; "Jonghwan Hyon"
<jerry@datacraft-korea.com>; <ccielab@groupstudy.com>
Sent: Saturday, February 17, 2001 4:36 PM
Subject: Re: How advertise loopback interface in IGRP update?
> You can also "redistribute connected" under the igrp process, although if
> the only connected network you want to advertise is the loopback, you'll
> have to filter the other connected networks from being redistributed into
> igrp (I believe this holds true even if you have all other connected
> interaces designated as passive interfaces under the IGRP process, as
> passive interface only stops 'outgoing' IGRP advertisements on that
> interface).
>
> Erick's solution is much simpler and the best way to go in "most" cases,
> although "redistributing connected" is something you should possess
> knowledge of in case you need it. For example, if you had 300 interfaces
in
> a router, you might not want to enter a "network x.x.x.x" command for
every
> interface under the IGRP process. It would probably be better to just
> redistribute the connected networks/subnets and filter as apporpriate.
>
>
> Dan Pontrelli
> Customer Installation Engineer - Verio NYC
> CCNP, MCSE, CNA
>
>
> ----- Original Message -----
> From: "Erick B." <erickbe@yahoo.com>
> To: "Jonghwan Hyon" <jerry@datacraft-korea.com>; <ccielab@groupstudy.com>
> Sent: Saturday, February 17, 2001 4:09 PM
> Subject: Re: How advertise loopback interface in IGRP update?
>
>
> > Just need to put the IP network you assigned to the
> > loopback under 'router igrp #' and it'll work fine.
> >
> > Check to make sure the IP networks are correct under
> > router igrp and that you specify the network under the
> > ethernet/serial/whatever interface connecting to other
> > router running IGRP on its interface connecting to
> > you.
> >
> > --- Jonghwan Hyon <jerry@datacraft-korea.com> wrote:
> > > Hi,
> > > I setup loopback interface and run IGRP routing
> > > protocol.
> > > I want to advertise the network set on loopback
> > > interface,
> > > but it is not advertized in IGRP!
> > > What I do miss? or there is a mean to advertise the
> > > loopback in IGRP?
> > >
> > > Sorry, my poor English!
> > > regards,
> > > ***********************************************
> > > Jonghwan Hyon(jerry), CCNP/CCDP
> > > Tel : 8242-487-4272
> > > Fax : 8242-487-4273
> > > Mobile : 8211-437-8883
> > > e-mail : jerry@datacraft-korea.com
> > > ***********************************************
> > >
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:28:52 GMT-3