From: Raymond May (raymay30@xxxxxxxxxxx)
Date: Wed Jan 31 2001 - 20:08:36 GMT-3
>From debug R3's number is 8358662, but R2 configured to call 8358664.
Calling Party Number i = 'A', 0x81, '8358661'
> Called Party Number i = 0xC1, '8358662' <<<<
>From: David M Anderson <dma@cisco.com>
>Reply-To: David M Anderson <dma@cisco.com>
>To: "Bolcer, Matt" <matt.bolcer@eds.com>, ccielab@groupstudy.com
>Subject: Re: basic isdn setup problem
>Date: Wed, 31 Jan 2001 09:02:35 -0800
>
>Matt,
>I would make sure the number you are dialing on R2 (in the dialer map
>statement) is the phone number that R3 is respectively assigned. If that
>doesn't solve your problem I would try getting rid of the PPP auth stuff
>and then do a shut no shut on the bri interface and see if that helps.
>David
>At 10:22 AM 01/31/2001 -0500, Bolcer, Matt wrote:
> >anyone see any reasons for the encap failures when the dialer map shows
>the
> >path and the isdn info is okay (supposedly)?
> >
> >R2----------------- Teltone ISDN Simulator ----------------- R3
> >
> >R2 config:
> >
> >!
> >interface BRI0
> > ip address 196.1.1.26 255.255.255.0
> > ip directed-broadcast
> > encapsulation ppp
> > no ip route-cache
> > dialer idle-timeout 90
> > dialer map ip 196.1.1.29 name r3 8358664
> > dialer-group 1
> > isdn switch-type basic-dms100
> > isdn spid1 0835866101
> > isdn spid2 0835866301
> > ppp authentication chap
> >!
> >ip classless
> >no ip http server
> >!
> >dialer-list 1 protocol ip permit
> >
> >
> >r2#sh isdn status
> >Global ISDN Switchtype = basic-dms100
> >ISDN BRI0 interface
> > dsl 0, interface ISDN Switchtype = basic-dms100
> > Layer 1 Status:
> > ACTIVE
> > Layer 2 Status:
> > TEI = 96, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> > I_Queue_Len 0, UI_Queue_Len 0
> > TEI = 97, Ces = 2, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> > I_Queue_Len 0, UI_Queue_Len 0
> > Spid Status:
> > TEI 96, ces = 1, state = 5(init)
> > spid1 configured, no LDN, spid1 sent, spid1 valid
> > Endpoint ID Info: epsf = 0, usid = 1, tid = 1
> > TEI 97, ces = 2, state = 5(init)
> > spid2 configured, no LDN, spid2 sent, spid2 valid
> > Endpoint ID Info: epsf = 0, usid = 3, tid = 1
> > Layer 3 Status:
> > 0 Active Layer 3 Call(s)
> > Activated dsl 0 CCBs = 0
> > The Free Channel Mask: 0x80000003
> >
> >r3 config:
> >!
> >interface BRI0
> > ip address 196.1.1.29 255.255.255.0
> > ip directed-broadcast
> > encapsulation ppp
> > no ip route-cache
> > logging event subif-link-status
> > dialer idle-timeout 90
> > dialer map ip 196.1.1.26 name r2 8358661
> > dialer-group 1
> > isdn switch-type basic-dms100
> > isdn spid1 0835866201
> > isdn spid2 0835866401
> > no fair-queue
> > ppp authentication chap
> >!
> >ip classless
> >ip route 164.56.2.132 255.255.255.252 192.168.4.1
> >no ip http server
> >!
> >access-list 99 permit 192.57.1.1
> >access-list 100 permit ip any any
> >dialer-list 1 protocol ip permit
> >
> >r3#sh isdn status
> >Global ISDN Switchtype = basic-dms100
> >ISDN BRI0 interface
> > dsl 0, interface ISDN Switchtype = basic-dms100
> > Layer 1 Status:
> > ACTIVE
> > Layer 2 Status:
> > TEI = 94, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> > I_Queue_Len 0, UI_Queue_Len 0
> > TEI = 95, Ces = 2, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> > I_Queue_Len 0, UI_Queue_Len 0
> > Spid Status:
> > TEI 94, ces = 1, state = 5(init)
> > spid1 configured, no LDN, spid1 sent, spid1 valid
> > Endpoint ID Info: epsf = 0, usid = 2, tid = 1
> > TEI 95, ces = 2, state = 5(init)
> > spid2 configured, no LDN, spid2 sent, spid2 valid
> > Endpoint ID Info: epsf = 0, usid = 4, tid = 1
> > Layer 3 Status:
> > 0 Active Layer 3 Call(s)
> > Activated dsl 0 CCBs = 0
> > The Free Channel Mask: 0x80000003
> > Total Allocated ISDN CCBs = 0
> >
> >r2#sh dialer map
> >Static dialer map ip 196.1.1.29 name r3 (8358662) on BRI0
> >
> >r3#sh dialer map
> >Static dialer map ip 196.1.1.26 name r2 (8358661) on BRI0
> >
> >r2#sh debug
> >Dial on demand:
> > Dial on demand events debugging is on
> >Generic IP:
> > IP packet debugging is on
> >PPP:
> > PPP packet display debugging is on
> >ISDN:
> > ISDN events debugging is on
> > ISDN Q931 packets debugging is on
> >
> > ISDN events debug DSLs. (On/Off/No DSL:1/0/-)
> > DSL 0 --> 1
> > 1 -
> >
> > ISDN Q931 packets debug DSLs. (On/Off/No DSL:1/0/-)
> > DSL 0 --> 1
> > 1 -
> >
> >r2# ping 196.1.1.29
> >Type escape sequence to abort.
> >Sending 5, 100-byte ICMP Echos to 196.1.1.29, timeout is 2 seconds:
> >
> >1d18h: IP: s=196.1.1.26 (local), d=196.1.1.29 (BRI0), len 100, sending
> >1d18h: BRI0 DDR: Dialing cause ip (s=196.1.1.26, d=196.1.1.29)
> >1d18h: BRI0 DDR: Attempting to dial 8358662
> >1d18h: ISDN BR0: Outgoing call id = 0x800A, dsl 0
> >1d18h: IP: s=196.1.1.26 (local), d=196.1.1.29 (BRI0), len 100,
>encapsulation
> >fai
> >led
> >1d18h: ISDN BR0: Event: Call to 8358662 at 64 Kb/s
> >1d18h: ISDN BR0: process_bri_call(): call id 0x800A, called_number
>8358662,
> >spee
> >d 64, call type DATA
> >1d18h: CC_CHAN_GetIdleChanbri: dsl 0
> >1d18h: Found idle channel B1
> >1d18h: ISDN BR0: TX -> SETUP pd = 8 callref = 0x0A
> >1d18h: Bearer Capability i = 0x8890
> >1d18h: Channel ID i = 0x83
> >1d18h: Called Party Number i = 0x80, '8358662'
> >1d18h: Sending Complete
> >1d18h: ISDN BR0: RX <- CALL_PROC pd = 8 callref = 0x8A
> >1d18h: Channel ID i = 0x89
> >1d18h: Locking Shift to Codeset 5
> >1d18h: Codeset 5 IE 0x2A i = 0x809402, '`=', 0x8307, '8358662',
> >0x8E0B2
> >0, 'TELTONE', 0x20, '2', 0x20
> >1d18h.: ISDN BR0: received HOST_PROCEEDING call_id 0x800A
> >1d18h: IP: s=196.1.1.26 (local), d=196.1.1.29 (BRI0), len 100, sending
> >1d18h: IP: s=196.1.1.26 (local), d=196.1.1.29 (BRI0), len 100,
>encapsulation
> >fai
> >led.
> >1d18h: IP: s=196.1.1.26 (local), d=196.1.1.29 (BRI0), len 100, sending
> >1d18h: IP: s=196.1.1.26 (local), d=196.1.1.29 (BRI0), len 100,
>encapsulation
> >fai
> >led.
> >1d18h: IP: s=196.1.1.26 (local), d=196.1.1.29 (BRI0), len 100, sending
> >1d18h: IP: s=196.1.1.26 (local), d=196.1.1.29 (BRI0), len 100,
>encapsulation
> >fai
> >led.
> >1d18h: IP: s=196.1.1.26 (local), d=196.1.1.29 (BRI0), len 100, sending
> >1d18h: IP: s=196.1.1.26 (local), d=196.1.1.29 (BRI0), len 100,
>encapsulation
> >fai
> >led.
> >Success rate is 0 percent (0/5)
> >r2#
> >1d18h: BRI0: wait for isdn carrier timeout, call id=0x800A
> >1d18h: ISDN BR0: Event: Hangup call to call id 0x800A ces = 1
> >1d18h: ISDN BR0: process_disconnect(): call id 0x800A, call type is DATA,
> >b_idb
> >0x2617CEC, ces 1
> >1d18h: ISDN BR0: TX -> DISCONNECT pd = 8 callref = 0x0A
> >1d18h: Cause i = 0x8090 - Normal call clearing
> >1d18h: ISDN BR0: RX <- RELEASE pd = 8 callref = 0x8A
> >1d18h: ISDN BR0: TX -> RELEASE_COMP pd = 8 callref = 0x0A
> >1d18h: ISDN BR0: received HOST_DISCONNECT_ACK call_id 0x800A
> >1d18h: ISDN BR0: HOST_DISCONNECT_ACK: call type is DATA
> >
> >
> >r3 debug...
> >
> >1d18h: ISDN BR0: RX <- SETUP pd = 8 callref = 0x34
> >1d18h: Bearer Capability i = 0x8890
> >1d18h: Channel ID i = 0x89
> >1d18h: Signal i = 0x40 - Alerting on - pattern 0
> >1d18h: ENDPOINT IDent i = 0x8281
> >1d18h: Calling Party Number i = 'A', 0x81, '8358661'
> >1d18h: Called Party Number i = 0xC1, '8358662'
> >1d18h: ISDN BR0: Incoming call id = 0x10, dsl 0
> >1d18h: ISDN BR0: received HOST_INCOMING_CALL call_id 0x10
> >1d18h: ISDN BR0: HOST_INCOMING_CALL: voice_answer_data = FALSE
> >1d18h: ISDN BR0: Event: Received a DATA call from 8358661 on B1 at 64
>Kb/s
> >1d18h: ISDN BR0: RM returned call_type 0 resource type 0
> >1d18h: ISDN BR0: TX -> CALL_PROC pd = 8 callref = 0xB4
> >1d18h: Channel ID i = 0x89
> >1d18h: ISDN BR0: isdn_send_connect(): msg 4, call id 0x10, ces 1 bchan 0,
> >call t
> >ype DATA
> >1d18h: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
> >1d18h: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 8358661
> >1d18h: ISDN BR0: received HOST_QUERY_RESPONSE call_id 0x10
> >1d18h: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 8358661
> >1d18h: ISDN BR0: RX <- RELEASE pd = 8 callref = 0x34
> >1d18h: Cause i = 0x8290 - Normal call clearing
> >1d18h: ISDN BR0: TX -> RELEASE_COMP pd = 8 callref = 0xB4
> >1d18h: ISDN BR0: received HOST_DISCONNECT_ACK call_id 0x10
> >1d18h: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from 8358661 ,
> >call la
> >sted 30 seconds
> >1d18h: ISDN BR0: HOST_DISCONNECT_ACK: call type is DATA
> >1d18h: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
> >
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:27:50 GMT-3