From: McCallum, Robert (Robert.McCallum@xxxxxxxxxxxxxxxxxx)
Date: Tue Jan 23 2001 - 14:59:56 GMT-3
Is there anyone else as mad as you to try it!!!!
-----Original Message-----
From: Robert DeVito [mailto:robertdevito@hotmail.com]
Sent: 23 January 2001 17:48
To: Robert.McCallum@let-it-be-thus.com; ccielab@groupstudy.com
Subject: RE: ISIS and BVI/IRB
Robert,
I will give that a try.. I will let you know.. Has anyone else tried ISIS
over IRB/BVI?
Thank you,
Robert
----Original Message Follows----
From: "McCallum, Robert" <Robert.McCallum@let-it-be-thus.com>
Reply-To: "McCallum, Robert" <Robert.McCallum@let-it-be-thus.com>
To: "'Robert DeVito'" <robertdevito@hotmail.com>, ccielab@groupstudy.com
Subject: RE: ISIS and BVI/IRB
Date: Tue, 23 Jan 2001 10:04:27 -0000
Isn't the circuit types wrong. Specify on both interfaces that you want the
circuit types to be level-1-2. I know that these are the defaults
"normally" but with the error message below it would say to me that the BVI
interface has defaulted to a L1 circuit.
-----Original Message-----
From: Robert DeVito [mailto:robertdevito@hotmail.com]
Sent: 23 January 2001 06:01
To: robertdevito@hotmail.com; ccielab@groupstudy.com
Subject: Re: ISIS and BVI/IRB
as a follow up to the below email, When doing a debug isis adj, I receive
the message:
ISIS-Adj: new SNPA **Unknown SNPA type** (BVI3), cir type L1
Any thoughts?
Thanks in advanced,
Robert
----Original Message Follows----
From: "Robert DeVito" <robertdevito@hotmail.com>
Reply-To: "Robert DeVito" <robertdevito@hotmail.com>
To: ccielab@groupstudy.com
Subject: ISIS and BVI/IRB
Date: Tue, 23 Jan 2001 05:13:53
I am trying to setup ISIS over a BVI port. I will make the topology simple:
Vlan 3 ISL Trunk
R5----------Cat5------R6
R5 never seams to see any ISIS LSA packets from R6. I have no problem
pinging.
I provided the relevant info below. Thanks!!!
Router 5:
clns routing
!
interface Ethernet0
ip address 140.10.150.5 255.255.255.0
no ip directed-broadcast
ip router isis
!
router isis
net 00.5555.5555.5555.00
If I do a "show clns is" I receive the following:
r5#sho clns is
System Id Interface State Type Priority Circuit Id Format
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++
Router 6
!
interface FastEthernet0/0
no ip address
duplex auto
speed auto
!
interface FastEthernet0/0.2
encapsulation isl 3
no ip redirects
bridge-group 3
!
interface BVI3
ip address 140.10.150.6 255.255.255.0
ip router isis
!
router isis
net 00.6666.6666.6666.00
!
bridge 3 protocol ieee
bridge 3 route ip
bridge 3 router clns
!
If I do a "show clns is" I receive the following:
r6#sho clns is
System Id Interface State Type Priority Circuit Id Format
5555.5555.5555 BV3 Init L2 128 0000.0000.0000.0Phase V
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:27:41 GMT-3