From: Claude-Vincent (claude_vincent@xxxxxxxxx)
Date: Wed Jan 17 2001 - 03:27:03 GMT-3
Bernard,
I use ntt as I am working in Tokyo with 2 ISDN lines.
Regarding the calls, I can ping from the 2504 (spoke1) now as I changed the
ISDN line used by the 2523 (hub) but I still cannot ping from the 2523.
Here is the debug. Note that the TEI given automatically by the ISDN switch
change after clearing the lines. Moreover, I receive a TEI=77 which I don't
know at all! Do you know why all this happen?
hub#clear int bri0
hub#
1d04h: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BRI0, TEI 79 changed to
down
1d04h: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 78 changed to up
hub#deb ppp authe
PPP authentication debugging is on
hub#sh deb
Dial on demand:
Dial on demand events debugging is on
PPP:
PPP authentication debugging is on
PPP protocol negotiation debugging is on
hub#ping 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
1d04h: BR0 DDR: Dialing cause ip (s=10.1.1.2, d=10.1.1.1)
1d04h: BR0 DDR: Attempting to dial XXXX.....
Success rate is 0 percent (0/5)
hub#deb isdn q921
ISDN Q921 packets debugging is on
hub#ping 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
1d04h: BR0 DDR: Dialing cause ip (s=10.1.1.2, d=10.1.1.1)
1d04h: BR0 DDR: Attempting to dial XXXX
1d04h: BRI0: call delayed. number redialed too soon
1d04h: BR0 DDR: Unable to dial XXXX..
1d04h: BR0 DDR: Dialing cause ip (s=10.1.1.2, d=10.1.1.1)
1d04h: BR0 DDR: Attempting to dial XXXX
1d04h: BRI0: call delayed. number redialed too soon
1d04h: BR0 DDR: Unable to dial XXXX..
1d04h: ISDN BR0: RX <- RRp sapi = 0 tei = 78 nr = 2
1d04h: ISDN BR0: TX -> RRf sapi = 0 tei = 78 nr = 5
1d04h: BR0 DDR: Dialing cause ip (s=10.1.1.2, d=10.1.1.1)
1d04h: BR0 DDR: Attempting to dial XXXX
1d04h: BRI0: call delayed. number redialed too soon
1d04h: BR0 DDR: Unable to dial XXXX.
1d04h: ISDN BR0: RX <- RRp sapi = 0 tei = 77 nr = 36 .
1d04h: BR0 DDR: Dialing cause ip (s=10.1.1.2, d=10.1.1.1)
1d04h: BR0 DDR: Attempting to dial XXXX
1d04h: BRI0: call delayed. number redialed too soon
1d04h: BR0 DDR: Unable to dial XXXX..
1d04h: BR0 DDR: Dialing cause ip (s=10.1.1.2, d=10.1.1.1)
1d04h: BR0 DDR: Attempting to dial XXXX
1d04h: BRI0: call delayed. number redialed too soon
1d04h: BR0 DDR: Unable to dial XXXX..
Success rate is 0 percent (0/5)
hub#
1d04h: ISDN BR0: RX <- RRp sapi = 0 tei = 78 nr = 2
1d04h: ISDN BR0: TX -> RRf sapi = 0 tei = 78 nr = 5
1d04h: ISDN BR0: RX <- RRp sapi = 0 tei = 77 nr = 36 <-where does this
TEI comes from? why?!!!!
1d04h: ISDN BR0: RX <- RRp sapi = 0 tei = 78 nr = 2
1d04h: ISDN BR0: TX -> RRf sapi = 0 tei = 78 nr = 5
1d04h: ISDN BR0: RX <- RRp sapi = 0 tei = 77 nr = 36 u all
All possible debugging has been turned off
Vincent
----- Original Message -----
From: "Bernard Dunn" <dunn@cisco.com>
To: "Claude-Vincent" <claude_vincent@yahoo.com>
Cc: "Santarsiero, Bill" <BSantarsiero@greenwichtech.com>; "'Ccielab"
<ccielab@groupstudy.com>
Sent: Tuesday, January 16, 2001 9:40 PM
Subject: Re: ISDN issue
> Vincent,
>
> How come you're using 'isdn switch-type ntt'?
>
> If there is a bearercap problem, you'd be consulting the network.. But
> since your debug has a call up, then it doesn't look like 'debug isdn
> q931' output.
>
> So what does other debugs look like -
>
> debug ppp negotiation
> debug ppp authentication
>
> 'show isdn status' after the call is up.
>
> Also assuming that your spoke router (2504) has all the 'username hub
> password' setup correctly.
>
> Regards
>
> Bernard.
>
>
> On Tue, 16 Jan 2001, Claude-Vincent wrote:
>
> > On my 2523:
> >
> > version 12.1
> > no service single-slot-reload-enable
> > service timestamps debug uptime
> > service timestamps log uptime
> > no service password-encryption
> > !
> > hostname hub
> > !
> > logging rate-limit console 10 except errors
> > !
> > username spoke1 password 0 cisco
> > ip subnet-zero
> > no ip finger
> > no ip domain-lookup
> > !
> > ...
> > !
> > isdn switch-type ntt
> > cns event-service server
> > interface BRI0
> > ip address 10.1.1.2 255.255.255.0
> > encapsulation ppp
> > dialer idle-timeout 300
> > dialer map ip 10.1.1.1 name spoke1 broadcast XXXX
> > dialer-group 1
> > isdn switch-type ntt
> > ppp authentication chap
> > !
> > ip kerberos source-interface any
> > ip classless
> > no ip http server
> > !
> > dialer-list 1 protocol ip permit
> >
> > ISDN stat:
> >
> > hub#sh isdn stat
> > Global ISDN Switchtype = ntt
> > ISDN BRI0 interface
> > dsl 0, interface ISDN Switchtype = ntt
> > Layer 1 Status:
> > ACTIVE
> > Layer 2 Status:
> > TEI = 70, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> > Layer 3 Status:
> > 0 Active Layer 3 Call(s)
> > Active dsl 0 CCBs = 0
> > The Free Channel Mask: 0x80000003
> > Total Allocated ISDN CCBs = 0
> >
> > On my 2504:
> >
> > interface BRI0
> > ip address 10.1.1.1 255.255.255.0
> > no ip directed-broadcast
> > encapsulation ppp
> > dialer idle-timeout 300
> > dialer map ip 10.1.1.2 name hub broadcast YYYY
> > dialer-group 1
> > isdn switch-type ntt
> > ppp authentication chap
> > !
> > no ip http server
> > ip classless
> > !
> > dialer-list 1 protocol ip permit
> > !
> >
> > ISDN Sta:
> >
> > spoke1#sh isdn stat
> > Global ISDN Switchtype = ntt
> > ISDN BRI0 interface
> > dsl 0, interface ISDN Switchtype = ntt
> > Layer 1 Status:
> > ACTIVE
> > Layer 2 Status:
> > TEI = 70, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> > Layer 3 Status:
> > 0 Active Layer 3 Call(s)
> > Activated dsl 0 CCBs = 0
> > Total Allocated ISDN CCBs = 0
> >
> > When I ping from the 2504, I have got:
> >
> > 00:40:43: Channel ID i = 0x89
> > 00:40:43: ISDN BR0: RX <- ALERTING pd = 8 callref = 0x86
> > 00:40:43: ISDN BR0: RX <- CONNECT pd = 8 callref = 0x86.
> > 00:40:43: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up...
> > 00:40:50: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to XXXX .
> > Success rate is 0 percent (0/5)
> > spoke1#ping 10.1.1.2
> >
> > Type escape sequence to abort.
> > Sending 5, 100-byte ICMP Echos to 10.1.1.2, timeout is 2 seconds:
> > .....
> > Success rate is 0 percent (0/5)
> >
> > And from the 2523:
> >
> > Type escape sequence to abort.
> > Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
> >
> > 00:39:46: ISDN BR0: TX -> SETUP pd = 8 callref = 0x04
> > 00:39:46: Bearer Capability i = 0x8890
> > 00:39:46: Channel ID i = 0x83
> > 00:39:46: Called Party Number i = 0x80, '0335113025',
Plan:Unknown,
> > Type
> > :Unknown
> > 00:39:46: ISDN BR0: RX <- CALL_PROC pd = 8 callref = 0x84
> > 00:39:46: Channel ID i = 0x89
> > 00:39:47: ISDN BR0: RX <- ALERTING pd = 8 callref = 0x84.
> > 00:39:47: ISDN BR0: RX <- CONNECT pd = 8 callref = 0x84
> > 00:39:47: ISDN BR0: HOST_CONNECT: VOICE ERROR: Bearer capability not
> > available(0
> > x3A): bchan 0, call id 0x8004....
> > Success rate is 0 percent (0/5)
> >
> >
> > Vincent
> >
> > ----- Original Message -----
> > From: "Santarsiero, Bill" <BSantarsiero@greenwichtech.com>
> > To: "'Claude-Vincent'" <claude_vincent@yahoo.com>; "'Ccielab"
> > <ccielab@groupstudy.com>
> > Sent: Monday, January 15, 2001 10:46 PM
> > Subject: RE:
> >
> >
> > > Can you do a "sho isdn status" and send that as well. Include your
> > configs
> > > for the two routers also.
> > >
> > > -----Original Message-----
> > > From: Claude-Vincent [mailto:claude_vincent@yahoo.com]
> > > Sent: Monday, January 15, 2001 5:30 AM
> > > To: 'Ccielab
> > > Subject:
> > >
> > > Dear all,
> > >
> > > I am playing with an ISDN line and I don't succeed to make it work!
Does
> > > anyone know what it means?
> > > Hub#ping 10.1.1.1
> > > Type escape sequence to abort.
> > > Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
> > > 1d07h: ISDN BR0: TX -> SETUP pd = 8 callref = 0x0D
> > > 1d07h: Bearer Capability i = 0x8890
> > > 1d07h: Channel ID i = 0x83
> > > 1d07h: Called Party Number i = 0x80, 'XXXX', Plan:Unknown,
> > > Type:Un
> > > known
> > > 1d07h: ISDN BR0: RX <- CALL_PROC pd = 8 callref = 0x8D 1d07h:
> > > Channel ID i = 0x89 1d07h: ISDN BR0: RX <- ALERTING pd = 8 callref =
> > 0x8D.
> > > 1d07h: ISDN BR0: RX <- CONNECT pd = 8 callref = 0x8D
> > > 1d07h: ISDN BR0: HOST_CONNECT: VOICE ERROR: Bearer capability not
> > > available(0x3A
> > > ): bchan 0, call id 0x800D....
> > > Success rate is 0 percent (0/5)
> > > Hub#u all
> > > All possible debugging has been turned off
> > > Hub#sh dial
> > >
> > > BRI0 - dialer type = ISDN
> > > Dial String Successes Failures Last DNIS Last status
> > > XXXX 0 0 00:00:20 failed
> > > 0 incoming call(s) have been screened.
> > > 0 incoming call(s) rejected for callback.
> > >
> > > BRI0:1 - dialer type = ISDN
> > > Idle timer (120 secs), Fast idle timer (20 secs)
> > > Wait for carrier (30 secs), Re-enable (15 secs)
> > > Dialer state is idle
> > > BRI0:2 - dialer type = ISDN
> > > Idle timer (120 secs), Fast idle timer (20 secs)
> > > Wait for carrier (30 secs), Re-enable (15 secs)
> > > Dialer state is idle
> > > Thanks
> > > Vincent
> > >
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:27:32 GMT-3