From: Merrill, James D. (AIT) (James.D.Merrill@xxxxxxxxxxxxxxxxx)
Date: Thu Jan 11 2001 - 16:47:58 GMT-3
ATM is a major piece of the R&S CCIE lab. When I took the LAB last November
you only had access to one side of the ATM connection. You have to be able
to pull IGP routing updates, and VoIP connectivity over the ATM connection.
I expect that starting in February when they pull AppleTalk off the LAB exam
that you may see more ATM not less.
There's a lot more ATM customization and tuning being used today in live
networks that aren't being addressed on the CCIE exam.
-----Original Message-----
From: Paulo Mendes De Oliveira [mailto:pmendesd@cisco.com]
Sent: Thursday, January 11, 2001 1:24 PM
To: Patrick Bikar
Cc: Justin Menga; ccielab@groupstudy.com
Subject: Re: Simple LS1010 config
Excuse my ignorance but according to
<http://www.cisco.com/warp/public/625/ccie/certifications/routing.html#43>
ATM
LANE is no longer in the Lab Exam. Although I can see that
only ATM LANE is
explicitly mentioned I also note from the equipment list
that no ATM switch
(LS1010) is included. Hence whey the ATM questions?
Am I missing something?
TIA
Patrick Bikar wrote:
> Justin,
>
> Thanks for the clear answer.
>
> Does it acctually mean that configuring SVCs on an LS1010
is simpler than
> configuring PVCs ?
>
> Don't you need to specify the atm-nsap prefix of the
switch ?
>
> Do you know what is configured by default (ilmi, qsaal,
...) ?
>
> Thanks for any hints !
> Patrick.
>
> At 22:09 11/01/2001 +1300, Justin Menga wrote:
> >Hi,
> >
> >All you need to do is start with a default configuration,
'no shut' on the
> >ATM access ports. You can do SVCs now.
> >
> >Then to add a PVC, on either of the PVC interfaces (not
both as you do for
> >frame relay) configure:
> >
> >int atm1/0/0
> > desc Connected to R1
> > atm pvc 0 100 int atm1/0/1 0 200
> >
> >int atm1/0/1
> > desc COnnected to R2
> >
> >R1 ---------- LS1010 --------- R2
> > (0/100) (0/200)
> >
> >
> >Regards,
> >
> >Justin Menga CCIE #6640 MCSE+I CCSE
> >WAN Specialist
> >Computerland New Zealand
> >PO Box 3631, Auckland
> >DDI: (+64) 9 360 4864 Mobile: (+64) 25 349 599
> >mailto: justin.menga@computerland.co.nz
> >
> >
> >
> >-----Original Message-----
> >From: Patrick Bikar [mailto:pbikar@cisco.com]
> >Sent: Thursday, January 11, 2001 9:36 PM
> >To: ccielab@groupstudy.com
> >Subject: Simple LS1010 config
> >
> >
> >Hi all !
> >
> >Could anyone send me a simple LS1010 config in order to
be able to set up
> >PVCs and SVCs between 2 routers with atm interfaces ? The
configs of the
> >routers are welcome also if possible.
> >
> >Thanks !
> >Patrick.
> >
> >
> >Patrick.
> >CCNP, Belgium.
> >Lab:15/03/2001
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:27:27 GMT-3