From: Richard Mott (richpmott@xxxxxxxxxxx)
Date: Thu Jan 11 2001 - 02:48:58 GMT-3
Having a solid foundation in the R/S certainly helped but the other
designations are just as tough.
Rich Mott
CCIE #5234 (R&S)(ISP/Dial)(Design)
Internetwork Solutions Engineer
Thrupoint INC
----Original Message Follows----
From: "fwells12" <fwells12@hotmail.com>
Reply-To: "fwells12" <fwells12@hotmail.com>
To: <ccielab@groupstudy.com>
Subject: Re: Using a 250x Router For Dial-Up
Date: Mon, 8 Jan 2001 22:22:17 -0800
That is quite some feat...getting three CCIE designations in a little over
one year! Are the other tracks easier than the R/S, or does having the R/S
give you a good solid foundation for building on, therefore making the
other CCIE tracks more attainable?
Oh, and now that you are one of a handful of triple CCIE's in the world,
hows life?
Cheers
----- Original Message -----
From: Richard Mott <richpmott@hotmail.com>
To: <david_fu@yahoo.com>; <ccielab@groupstudy.com>
Sent: Tuesday, January 09, 2001 4:21 AM
Subject: Re: Using a 250x Router For Dial-Up
> You can try something similar to the following config.
>
> Rich Mott
> CCIE #5234 (R&S)(ISP/Dial)(Design)
> Internetwork Solutions Engineer
> Thrupoint INC
>
> Configuration
>
> !
> version 11.3
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname myrouter
> !
> !
> username loginid password mypassword
> ip subnet-zero
>
> ip nat pool isp-nat 199.9.9.37 199.9.9.37 netmask 255.255.255.224
> ip nat inside source list 101 pool isp-nat overload
> no ip domain-lookup
> chat-script dial "" "ATDT5551234" TIMEOUT 60 CONNECT /c
> !
> !
> !
> interface Ethernet0
> ip address 10.1.1.1 255.255.255.0
> ip nat inside
> !
> !
> interface Async9
> no ip address
> encapsulation ppp
> dialer in-band
> dialer pool-member 1
> async mode dedicated
> no fair-queue
> no cdp enable
> ppp authentication chap
> !
> interface Dialer1
> ip address negotiated
> ip nat outside
> encapsulation ppp
> dialer remote-name r5
> dialer string 5551234
> dialer pool 1
> dialer-group 1
> no cdp enable
> ppp authentication chap
> !
> !
> ip classless
> ip route 0.0.0.0 0.0.0.0 Dialer1
> !
>
> access-list 101 permit ip 10.0.0.0 0.255.255.255 any
> dialer-list 1 protocol ip permit
> !
> line con 0
>
> line aux 0
> script dialer dial
> modem InOut
> modem autoconfigure type usr_sportster
> speed 38400
> flowcontrol hardware
> line vty 0 4
> login
> !
> end
>
>
>
>
> ----Original Message Follows----
> From: David Fu <david_fu@yahoo.com>
> Reply-To: David Fu <david_fu@yahoo.com>
> To: ccielab@groupstudy.com
> Subject: Using a 250x Router For Dial-Up
> Date: Mon, 8 Jan 2001 18:06:59 -0800 (PST)
>
> Hi,
>
> I wonder if it's possible to use a modem and an aux
> port off a 2507 router to dial out into an ISP,
> obtains an IP address and a default-gateway (via
> DHCP)which becomes a default route.
>
> I was hoping for a way to use this router to share
> Internet access among two hosts. We'd need to do NAT
> too if possible.
>
> Any suggestion?
>
> David
>
>
>
> =====
> David_Fu@yahoo.com
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:27:27 GMT-3