From: Dave (cisco_instructor@xxxxxxxxxx)
Date: Tue Jan 09 2001 - 17:38:27 GMT-3
use the broadcast key word on the pvc, and it works fine...
d-
----- Original Message -----
From: "Kevin Baumgartner" <kbaumgar@cisco.com>
To: "Ronnie Royston" <RonnieR@globaldatasys.com>; "'Robert DeVito'"
<robertdevito@hotmail.com>; <cciecn@yahoo.com>; <abaskerville@ibeam.com>;
<Simon.Baxter@au.logical.com>; <ccielab@groupstudy.com>
Sent: Tuesday, January 09, 2001 1:18 PM
Subject: RE: EIGRP over ATM
> So doing Eigrp over ATM using PVC's, or SVC's is no problem.
>
> Doing it over CLIP doesn't look possible. Or certainly unstable.
> One of the limitations is how does the ARP server
> contact the client routers if it needs to send a routing update and
> there is no connection already setup between the client and ARP server?
> The CLIP ARP server has no way of setting up a connect. This is not part
> of the CLIP specification.
>
> Kevin
>
> At 12:01 PM 1/9/01 -0600, Ronnie Royston wrote:
> >This setup should take about 45 seconds; it's very simple. There are no
> >pitfalls here.
> >
> >Interface ATM 0
> >ip add x.x.x.1 /24
> >pvc 1/35
> > protocol ip x.x.x.2 broad
> >no shut
> >!
> >router eigrp 10
> > network x.x.x.0 /24
> >
> >If you're having problems with the link going up and down, check the
cabling
> >and/or the switch if you have one between your two routers. If it asks
you
> >to set bit rates, all the commands are in pvc config mode.
> >
> >-----Original Message-----
> >From: Robert DeVito [mailto:robertdevito@hotmail.com]
> >Sent: Tuesday, January 09, 2001 9:50 AM
> >To: cciecn@yahoo.com; abaskerville@ibeam.com;
> >Simon.Baxter@au.logical.com; ccielab@groupstudy.com
> >Subject: RE: EIGRP over ATM
> >
> >
> >I plan on working on ATM next week. Do you need the neighbor command in
> >EIGRP?
> >
> >Robert
> >
> >
> >----Original Message Follows----
> >From: Jack Yu <cciecn@yahoo.com>
> >Reply-To: Jack Yu <cciecn@yahoo.com>
> >To: Allyn Baskerville <abaskerville@ibeam.com>, "'Simon Baxter'"
> ><Simon.Baxter@au.logical.com>, ccielab@groupstudy.com
> >Subject: RE: EIGRP over ATM
> >Date: Tue, 9 Jan 2001 08:09:21 -0800 (PST)
> >
> >Simon,
> >
> >How about taking off the neighbor command from the
> >eigrp config?
> >
> >Good Luck
> >
> >Jack
> >--- Allyn Baskerville <abaskerville@ibeam.com> wrote:
> > > I just gave this a shot, but still no success.
> > > Thanks for the response,
> > > though. Allyn
> > >
> > > -----Original Message-----
> > > From: Simon Baxter
> > > [mailto:Simon.Baxter@au.logical.com]
> > > Sent: Thursday, January 04, 2001 1:08 AM
> > > To: Allyn Baskerville; ccielab@groupstudy.com
> > > Subject: RE: EIGRP over ATM
> > >
> > >
> > > Use : "protocol ip 172.32.1.15 broadcast"
> > >
> > > -----Original Message-----
> > > From: Allyn Baskerville
> > > [mailto:abaskerville@ibeam.com]
> > > Sent: Thursday, January 04, 2001 3:33 PM
> > > To: ccielab@groupstudy.com
> > > Subject: EIGRP over ATM
> > >
> > >
> > > I ran into a problem today that I can't seem to
> > > resolve. I am experiencing
> > > a problem with EIGRP neighbors staying up over an
> > > ATM link when using either
> > > PVCs, SVCs or classical IP. The symptoms are exactly
> > > the same for all of
> > > these. However, I'm not having problems with other
> > > routing protocols. The
> > > neighbors will come up for 5 seconds, go down for 5
> > > seconds. I do see
> > > hellos on both routers, though:
> > >
> > > 01:31:58: EIGRP: Sending HELLO on ATM3/0 nbr
> > > 172.32.1.15
> > > 01:31:58: AS 10, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ
> > > un/rely 0/0
> > > 01:31:59: EIGRP: Received HELLO on ATM3/0 nbr
> > > 172.32.1.15
> > > 01:31:59: AS 10, Flags 0x0, Seq 0/0 idbQ 0/0
> > > 01:32:03: EIGRP: Sending HELLO on ATM3/0 nbr
> > > 172.32.1.15
> > >
> > > The routers are running 12.0.7T, and I reloaded them
> > > and the ATM switch a
> > > couple of times. Do any of you have an idea that I
> > > might try? Incidentally,
> > > both routers (at least for the PVC configuration)
> > > are configured as follows,
> > > only the IP and PVC information is changed between
> > > the two:
> > >
> > > interface ATM3/0
> > > bandwidth 155000
> > > ip address 172.32.1.16 255.255.255.0
> > > ip directed-broadcast
> > > no ip route-cache
> > > no ip mroute-cache
> > > no atm ilmi-keepalive
> > > pvc toR15 1/116
> > > protocol ip 172.32.1.15
> > > broadcast
> > >
> > > router eigrp 10
> > > network 172.22.0.0
> > > network 172.32.0.0
> > > neighbor 172.32.1.15 ATM3/0
> > > no auto-summary
> > >
> > >
> > > Thanks - Allyn
> > >
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:27:25 GMT-3