From: Kevin Baumgartner (kbaumgar@xxxxxxxxx)
Date: Thu Sep 28 2000 - 13:23:26 GMT-3
I have done that lab and it uses ILMI. My mistake should have said
PVC 0/16 for ILMI.
So how is the SVC call setup done if ILMI is not used? I'm open to
suggestions. Doing ATM routes on the LS1010 only route where the NSAP
address will go once in the switch.
Even if it's possible to do SVC by a configuration on the LS1010 (which
I doubt) without ILMI what's the point. I don't believe in the lab you
get access to the LS1010.
Kevin
>
> Nope, can definately be done. References in the archives to people having
> done it, and Marc at CCBootcamp specifically tells people to practise it in
> a note at the end of one lab (lab14).
>
> By the way, you say there that esi is the 'prefix' - important distinction
> here, the prefix identifies the SWITCH the esi (end system identifier) -
> uniquely id.s the attached device. ILMI also should be on VCI 16 (usually).
>
> Anyway, I recieved a config from sb. - apparently I need a bit more config
> on the ls.
>
> I tell it tomorrow and let you know what happens! Either way I'll know!!
>
> Mark
>
>
> >From: Kevin Baumgartner <kbaumgar@cisco.com>
> >To: markl11@hotmail.com
> >Subject: Re: ATM gurus...heeeelllp!!!
> >Date: Thu, 28 Sep 2000 08:17:14 -0700 (PDT)
> >
> > You can't do ATM SVC without ILMI. The nsap-addr is the full length
> >atm svc address where the atm esi-address is just a prefix of the
> >nsap-address.
> >Neither mean that you don't use ILMI.
> >
> > Add
> >
> > ATM PVC 2 0 15 ilmi
> >
> > Kevin
> >
> > >
> > >
> > > Hi Gurus,
> > >
> > > ATM SVCs WITHOUT ILMI.
> > > ----------------------
> > >
> > > Wonder if you can offer a little help.
> > >
> > > I've been configuring atm svcs using the 'atm esi-address' command
> >without
> > > any problems (this command requires the use of ilmi).
> > >
> > > However, if I'm not allowed to use ilmi (no atm pvc 1 0 16 ilmi) then it
> > > seems to me that the command I need is 'atm nsap-address'. Now I know
> >that
> > > these two commands do bascially the same thing (but 'atm esi-address'
> >allows
> > > you to be slightly lazier (very appealing!)), but in the Cisco IOS WAN
> > > Networking Solutions manual (the one for 11.x) it strongly implies that
> >the
> > > '..nsap-addr..' command CAN be used without ilmi.
> > >
> > > Now here's the crux of the problem: I can't get it to work!
> > >
> > > My config is very simple, two routers either side of ls1010, both with
> > > approximately the following config:
> > >
> > > int atm0/0
> > > atm pvc 1 0 5 qsaal
> > > atm nsap-address xxx(prefix)xxx.123456789012.00
> > > ip address xxxxx yyyyy
> > >
> > >
> > > ESI is of course unique on each router.
> > >
> > > Now the moment I use '..esi-address' & ilmi, it starts working.
> > >
> > > So, how do I get SVCs WITHOUT ilmi to work???
> > >
> > > Thanks v.much in advance,
> > >
> > > Mark
> > >
> > > P.S. I know that it's possible to get it to work by turning on ilmi
> > > temporarily (so that prefix & esi are exchanged), but I need a real
> > > solution.
> > >
> > >
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:25:08 GMT-3