From: Mark Lewis (markl11@xxxxxxxxxxx)
Date: Thu Sep 28 2000 - 12:01:01 GMT-3
Like this:
ls1010#
ls1010#
ls1010#sh run
Building configuration...
Current configuration:
!
version 12.0
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname ls1010
!
!
ip subnet-zero
!
atm lecs-address-default 47.0091.8100.0000.00d0.baf3.3b01.0010.7ba3.a703.00
1
atm lecs-address-default 47.0091.8100.0000.00d0.baf3.3b01.0010.7b8f.e783.00
2
atm address 47.0091.8100.0000.00d0.baf3.3b01.00d0.baf3.3b01.00
atm router pnni
no aesa embedded-number left-justified
node 1 level 56 lowest
redistribute atm-static
!
!
process-max-time 200
!
interface ATM0/1/0
no ip address
no ip directed-broadcast
no atm ilmi-keepalive
!
interface ATM0/1/1
no ip address
no ip directed-broadcast
no atm ilmi-keepalive
atm pvc 0 50 interface ATM0/1/0 5 255
atm pvc 4 44 interface ATM0/1/0 5 55
!
interface ATM0/1/2
no ip address
no ip directed-broadcast
no atm ilmi-keepalive
atm pvc 0 255 interface ATM0/1/1 0 45
!
(By they way, I know there's alot of other stuff in there, pvcs,lecs
addresses,etc. - I was using those for other things)
(My two routers are hanging off 0/1/1 & 0/1/0)
>From: "Connary, Julie Ann" <jconnary@cisco.com>
>To: "Mark Lewis" <markl11@hotmail.com>
>Subject: Re: ATM gurus...heeeelllp!!!
>Date: Thu, 28 Sep 2000 10:44:45 -0400
>
>What does your ls1010 setup look like?
>
>
>
>At 02:24 PM 9/28/2000 +0000, you wrote:
>
>>Hi Gurus,
>>
>>ATM SVCs WITHOUT ILMI.
>>----------------------
>>
>>Wonder if you can offer a little help.
>>
>>I've been configuring atm svcs using the 'atm esi-address' command without
>>any problems (this command requires the use of ilmi).
>>
>>However, if I'm not allowed to use ilmi (no atm pvc 1 0 16 ilmi) then it
>>seems to me that the command I need is 'atm nsap-address'. Now I know that
>>these two commands do bascially the same thing (but 'atm esi-address'
>>allows you to be slightly lazier (very appealing!)), but in the Cisco IOS
>>WAN Networking Solutions manual (the one for 11.x) it strongly implies
>>that the '..nsap-addr..' command CAN be used without ilmi.
>>
>>Now here's the crux of the problem: I can't get it to work!
>>
>>My config is very simple, two routers either side of ls1010, both with
>>approximately the following config:
>>
>>int atm0/0
>>atm pvc 1 0 5 qsaal
>>atm nsap-address xxx(prefix)xxx.123456789012.00
>>ip address xxxxx yyyyy
>>
>>
>>ESI is of course unique on each router.
>>
>>Now the moment I use '..esi-address' & ilmi, it starts working.
>>
>>So, how do I get SVCs WITHOUT ilmi to work???
>>
>>Thanks v.much in advance,
>>
>>Mark
>>
>>P.S. I know that it's possible to get it to work by turning on ilmi
>>temporarily (so that prefix & esi are exchanged), but I need a real
>>solution.
>>
>>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:25:08 GMT-3