From: William Swedberg (swedbergwp@xxxxxxxxx)
Date: Thu Aug 24 2000 - 14:35:17 GMT-3
I have not played with dialer watch lists but here
goes. I don't see the "broadcast" key word on you
dialer map 3.3.0.0. Cisco's example has this in the
map. Also, is the sho ip route for the same router as
the config. You have a static route to 0.0.0.0 going
out ser0. You won't get traffic out the asyn with
that route installed. Your line dials because you are
ping the other bri interface. The router will route
on longest match.
When you post the configs, please post the entire
config because the problem may be in another part of
your config that is not shown.
William Swedberg CCNP CCDP
--- khalid siddiq <khalidsi@hotmail.com> wrote:
> hi all,
> i am facing some problem with the dialer watch-list,
> my router detect that the watch network is down but
> unable to dial,
> i am attaching the configuration.
> any comment is appriciated.
>
> router 1:
>
>
> interface Async4
> ip address 10.60.0.2 255.255.0.0
> encapsulation ppp
> bandwidth 33
> dialer in-band
> dialer map ip 2.0.0.0 broadcast 7774267
> dialer map ip 3.3.0.0 name pdn 7774267
> dialer map ip 10.60.0.1 broadcast 7774267
> dialer watch-group 1
> dialer-group 1
> async mode dedicated
> no peer default ip address
> no cdp enable
> ppp pap sent-username khalid password 7
> 05000E0E2D454A02
>
>
> router eigrp 1
> redistribute static
> network 10.0.0.0
>
>
> access-list 101 deny eigrp any any log
> access-list 101 permit ip any any log
>
>
> dialer watch-list 1 ip 3.3.0.0 255.255.0.0
> dialer watch-list 1 ip 2.0.0.0 255.0.0.0
>
> dialer-list 1 protocol ip list 101
>
>
>
> sh ip route is ,
> router#sh ip route
> Codes: C - connected, S - static, I - IGRP, R - RIP,
> M - mobile, B - BGP
> D - EIGRP, EX - EIGRP external, O - OSPF, IA
> - OSPF inter area
> N1 - OSPF NSSA external type 1, N2 - OSPF
> NSSA external type 2
> E1 - OSPF external type 1, E2 - OSPF external
> type 2, E - EGP
> i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS
> level-2, * - candidate
> default
> U - per-user static route, o - ODR
>
> Gateway of last resort is 0.0.0.0 to network 0.0.0.0
>
> D 2.0.0.0/8 [90/10639872] via 10.3.0.17,
> 00:00:20, Serial1
> 3.0.0.0/16 is subnetted, 1 subnets
> D 3.3.0.0 [90/10639872] via 10.3.0.17,
> 00:00:05, Serial1
> 203.135.1.0/30 is subnetted, 1 subnets
> C 203.135.1.232 is directly connected, Serial0
> 10.0.0.0/8 is variably subnetted, 5 subnets, 3
> masks
> D 10.0.0.0/16 [90/10537472] via 10.3.0.17,
> 22:10:30, Serial1
> C 10.1.0.0/16 is directly connected, Ethernet0
> C 10.3.0.16/30 is directly connected, Serial1
> C 10.60.0.0/16 is directly connected, Async4
> S 10.60.0.1/32 is directly connected, Async4
> S* 0.0.0.0/0 is directly connected, Serial0
>
>
> and when the route 2.0.0.0 and 3.3.0.0 is removed.
>
> Aug 24 13:01:00.161: Dialer Watch: watch-group = 1
> Aug 24 13:01:00.161: network
> 3.3.0.0/255.255.0.0 DOWN,
> Aug 24 13:01:00.165: network 2.0.0.0/255.0.0.0
> UP,
> Aug 24 13:01:00.169: primary UP
> Aug 24 13:01:01.253: Dialer Watch: watch-group = 1
> Aug 24 13:01:01.253: network
> 3.3.0.0/255.255.0.0 DOWN,
> Aug 24 13:01:01.257: network 2.0.0.0/255.0.0.0
> UP,
> Aug 24 13:01:01.257: primary UP
> Aug 24 13:01:23.555: Dialer Watch: watch-group = 1
> Aug 24 13:01:23.555: network
> 3.3.0.0/255.255.0.0 DOWN,
> Aug 24 13:01:23.559: network 2.0.0.0/255.0.0.0
> DOWN,
> Aug 24 13:01:23.559: primary DOWN
> Aug 24 13:01:23.563: Dialer Watch: Dial Reason:
> Primary of group 1 down
> Aug 24 13:01:23.563: Dialer Watch: watch-group = 1,
> Aug 24 13:01:24.575: Dialer Watch: watch-group = 1
> Aug 24 13:01:24.575: network
> 3.3.0.0/255.255.0.0 DOWN,
> Aug 24 13:01:24.579: network 2.0.0.0/255.0.0.0
> DOWN,
> Aug 24 13:01:24.579: primary DOWN
> Aug 24 13:01:24.579: Dialer Watch: Dial Reason:
> Primary of group 1 down
> Aug 24 13:01:24.583: Dialer Watch: watch-group = 1,
>
> no dialing ????
> but when i ping 10.60.0.1,
> 1#ping 10.60.0.1
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 10.60.0.1, timeout
> is 2 seconds:
>
> Aug 24 13:12:33.782: Async4: Dialing cause ip
> (s=10.60.0.2, d=10.60.0.1)
> Aug 24 13:12:33.782: Async4: Attempting to dial
> 7774267
> Aug 24 13:12:33.782: CHAT4: Attempting async line
> dialer script
> Aug 24 13:12:33.786: CHAT4: no matching chat script
> found for 7774267
> Aug 24 13:12:33.786: CHAT4: Dialing using Modem
> script:
> d0efault-d0ials0cript &
> System script: none
> Aug 24 13:12:33.798: CHAT4: process started
> Aug 24 13:12:33.798: CHAT4: Asserting DTR
> Aug 24 13:12:33.802: CHAT4: Chat script
> d0efault-d0ials0cript started.....
> Success rate is 0 percent (0/5)
> NETS1#
> Aug 24 13:12:52.850: CHAT4: Chat script
> d0efault-d0ials0cript finished,
> status =
> Success
> Aug 24 13:12:52.858: As4 IPCP: Install route to
> 10.60.0.1
> Aug 24 18:12:54.854: %LINK-3-UPDOWN: Interface
> Async4, changed state to up
> Aug 24 13:12:54.886: As4 PPP: Treating connection as
> a callout
> Aug 24 13:12:54.886: As4 PPP: Phase is ESTABLISHING,
> Active Open
> Aug 24 13:12:54.890: As4 LCP: O CONFREQ [Closed] id
> 177 len 20
> Aug 24 13:12:54.894: As4 LCP: ACCM 0x000A0000
> (0x0206000A0000)
> Aug 24 13:12:54.894: As4 LCP: MagicNumber
> 0x210C8DD7 (0x0506210C8DD7)
> Aug 24 13:12:54.898: As4 LCP: PFC (0x0702)
> Aug 24 13:12:54.898: As4 LCP: ACFC (0x0802)
> Aug 24 13:12:55.078: As4 LCP: I CONFREQ [REQsent] id
> 9 len 24
> Aug 24 13:12:55.082: As4 LCP: ACCM 0x000A0000
> (0x0206000A0000)
> Aug 24 13:12:55.082: As4 LCP: AuthProto PAP
> (0x0304C023)
> Aug 24 13:12:55.086: As4 LCP: MagicNumber
> 0x04563C71 (0x050604563C71)
> Aug 24 13:12:55.090: As4 LCP: PFC (0x0702)
> Aug 24 13:12:55.126: As4 LCP: PFC (0x0702)
> Aug 24 13:12:55.130: As4 LCP: ACFC (0x0802)
> Aug 24 13:12:55.130: As4 LCP: State is Open
> Aug 24 13:12:55.134: As4 PPP: Phase is
> AUTHENTICATING, by the peer
> Aug 24 13:12:55.138: As4 PAP: O AUTH-REQ id 2 len 19
> from "khalid"
> Aug 24 13:12:55.266: As4 PAP: I AUTH-ACK id 2 len 5
> Aug 24 13:12:55.266: As4 PPP: Phase is UP
> Aug 24 13:12:55.270: As4 IPCP: O CONFREQ [Closed] id
> 102 len 10
> Aug 24 13:12:55.274: As4 IPCP: Address 10.60.0.2
> (0x03060A3C0002)
> Aug 24 13:12:55.290: As4 IPCP: I CONFREQ [REQsent]
> id 40 len 10
> Aug 24 13:12:55.294: As4 IPCP: Address 10.60.0.1
> (0x03060A3C0001)
> Aug 24 13:12:55.294: As4 IPCP: O CONFNAK [REQsent]
> id 40 len 10
> Aug 24 13:12:55.298: As4 IPCP: Address 2.0.0.0
> (0x030602000000)
> Aug 24 13:12:55.526: As4 IPCP: I CONFACK [REQsent]
> id 102 len 10
> Aug 24 13:12:55.530: As4 IPCP: Address 10.60.0.2
> (0x03060A3C0002)
> Aug 24 13:12:55.530: As4 IPCP: I CONFREQ [ACKrcvd]
> id 41 len 4
> Aug 24 13:12:55.534: As4 IPCP: O CONFACK [ACKrcvd]
> id 41 len 4
> Aug 24 13:12:55.538: As4 IPCP: State is Open
> Aug 24 13:12:56.290: dialer Protocol up for As4
> Aug 24 13:12:56.294: As4 IPCP: Remove route to
> 10.60.0.1
> Aug 24 18:12:56.334: %LINEPROTO-5-UPDOWN: Line
> protocol on Interface Async4,
>
=== message truncated ===
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:24:29 GMT-3