From: Geatti (geatti@xxxxxxxx)
Date: Thu Aug 24 2000 - 16:11:51 GMT-3
Does it dial and route without the watch-list? Make sure you config works
without the watch-list and eigrp deny on 101, does eigrp route over the
line? Can you ping over the line to the other loopback?
If you are routing over modems try the commands (on both ends)
async default routing
async dynamic routing
without these commands I don't believe routing behaves itself. Your line
seems to be coming up and the route 10.60.0.1 is removed immediately on
coming up. This happened to me and the commands above seemed to do the
trick.
I don't believe you need the commands;
dialer map ip 2.0.0.0 broadcast 7774267
dialer map ip 3.3.0.0 name pdn 7774267
Let us know if this doesn't or does work.
Marco
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
khalid siddiq
Sent: Thursday, August 24, 2000 9:24 AM
To: ccielab@groupstudy.com
Subject: dialer watch-list
hi all,
i am facing some problem with the dialer watch-list,
my router detect that the watch network is down but unable to dial,
i am attaching the configuration.
any comment is appriciated.
router 1:
interface Async4
ip address 10.60.0.2 255.255.0.0
encapsulation ppp
bandwidth 33
dialer in-band
dialer map ip 2.0.0.0 broadcast 7774267
dialer map ip 3.3.0.0 name pdn 7774267
dialer map ip 10.60.0.1 broadcast 7774267
dialer watch-group 1
dialer-group 1
async mode dedicated
no peer default ip address
no cdp enable
ppp pap sent-username khalid password 7 05000E0E2D454A02
router eigrp 1
redistribute static
network 10.0.0.0
access-list 101 deny eigrp any any log
access-list 101 permit ip any any log
dialer watch-list 1 ip 3.3.0.0 255.255.0.0
dialer watch-list 1 ip 2.0.0.0 255.0.0.0
dialer-list 1 protocol ip list 101
sh ip route is ,
router#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate
default
U - per-user static route, o - ODR
Gateway of last resort is 0.0.0.0 to network 0.0.0.0
D 2.0.0.0/8 [90/10639872] via 10.3.0.17, 00:00:20, Serial1
3.0.0.0/16 is subnetted, 1 subnets
D 3.3.0.0 [90/10639872] via 10.3.0.17, 00:00:05, Serial1
203.135.1.0/30 is subnetted, 1 subnets
C 203.135.1.232 is directly connected, Serial0
10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks
D 10.0.0.0/16 [90/10537472] via 10.3.0.17, 22:10:30, Serial1
C 10.1.0.0/16 is directly connected, Ethernet0
C 10.3.0.16/30 is directly connected, Serial1
C 10.60.0.0/16 is directly connected, Async4
S 10.60.0.1/32 is directly connected, Async4
S* 0.0.0.0/0 is directly connected, Serial0
and when the route 2.0.0.0 and 3.3.0.0 is removed.
Aug 24 13:01:00.161: Dialer Watch: watch-group = 1
Aug 24 13:01:00.161: network 3.3.0.0/255.255.0.0 DOWN,
Aug 24 13:01:00.165: network 2.0.0.0/255.0.0.0 UP,
Aug 24 13:01:00.169: primary UP
Aug 24 13:01:01.253: Dialer Watch: watch-group = 1
Aug 24 13:01:01.253: network 3.3.0.0/255.255.0.0 DOWN,
Aug 24 13:01:01.257: network 2.0.0.0/255.0.0.0 UP,
Aug 24 13:01:01.257: primary UP
Aug 24 13:01:23.555: Dialer Watch: watch-group = 1
Aug 24 13:01:23.555: network 3.3.0.0/255.255.0.0 DOWN,
Aug 24 13:01:23.559: network 2.0.0.0/255.0.0.0 DOWN,
Aug 24 13:01:23.559: primary DOWN
Aug 24 13:01:23.563: Dialer Watch: Dial Reason: Primary of group 1 down
Aug 24 13:01:23.563: Dialer Watch: watch-group = 1,
Aug 24 13:01:24.575: Dialer Watch: watch-group = 1
Aug 24 13:01:24.575: network 3.3.0.0/255.255.0.0 DOWN,
Aug 24 13:01:24.579: network 2.0.0.0/255.0.0.0 DOWN,
Aug 24 13:01:24.579: primary DOWN
Aug 24 13:01:24.579: Dialer Watch: Dial Reason: Primary of group 1 down
Aug 24 13:01:24.583: Dialer Watch: watch-group = 1,
no dialing ????
but when i ping 10.60.0.1,
1#ping 10.60.0.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.60.0.1, timeout is 2 seconds:
Aug 24 13:12:33.782: Async4: Dialing cause ip (s=10.60.0.2, d=10.60.0.1)
Aug 24 13:12:33.782: Async4: Attempting to dial 7774267
Aug 24 13:12:33.782: CHAT4: Attempting async line dialer script
Aug 24 13:12:33.786: CHAT4: no matching chat script found for 7774267
Aug 24 13:12:33.786: CHAT4: Dialing using Modem script:
d0efault-d0ials0cript &
System script: none
Aug 24 13:12:33.798: CHAT4: process started
Aug 24 13:12:33.798: CHAT4: Asserting DTR
Aug 24 13:12:33.802: CHAT4: Chat script d0efault-d0ials0cript started.....
Success rate is 0 percent (0/5)
NETS1#
Aug 24 13:12:52.850: CHAT4: Chat script d0efault-d0ials0cript finished,
status =
Success
Aug 24 13:12:52.858: As4 IPCP: Install route to 10.60.0.1
Aug 24 18:12:54.854: %LINK-3-UPDOWN: Interface Async4, changed state to up
Aug 24 13:12:54.886: As4 PPP: Treating connection as a callout
Aug 24 13:12:54.886: As4 PPP: Phase is ESTABLISHING, Active Open
Aug 24 13:12:54.890: As4 LCP: O CONFREQ [Closed] id 177 len 20
Aug 24 13:12:54.894: As4 LCP: ACCM 0x000A0000 (0x0206000A0000)
Aug 24 13:12:54.894: As4 LCP: MagicNumber 0x210C8DD7 (0x0506210C8DD7)
Aug 24 13:12:54.898: As4 LCP: PFC (0x0702)
Aug 24 13:12:54.898: As4 LCP: ACFC (0x0802)
Aug 24 13:12:55.078: As4 LCP: I CONFREQ [REQsent] id 9 len 24
Aug 24 13:12:55.082: As4 LCP: ACCM 0x000A0000 (0x0206000A0000)
Aug 24 13:12:55.082: As4 LCP: AuthProto PAP (0x0304C023)
Aug 24 13:12:55.086: As4 LCP: MagicNumber 0x04563C71 (0x050604563C71)
Aug 24 13:12:55.090: As4 LCP: PFC (0x0702)
Aug 24 13:12:55.126: As4 LCP: PFC (0x0702)
Aug 24 13:12:55.130: As4 LCP: ACFC (0x0802)
Aug 24 13:12:55.130: As4 LCP: State is Open
Aug 24 13:12:55.134: As4 PPP: Phase is AUTHENTICATING, by the peer
Aug 24 13:12:55.138: As4 PAP: O AUTH-REQ id 2 len 19 from "khalid"
Aug 24 13:12:55.266: As4 PAP: I AUTH-ACK id 2 len 5
Aug 24 13:12:55.266: As4 PPP: Phase is UP
Aug 24 13:12:55.270: As4 IPCP: O CONFREQ [Closed] id 102 len 10
Aug 24 13:12:55.274: As4 IPCP: Address 10.60.0.2 (0x03060A3C0002)
Aug 24 13:12:55.290: As4 IPCP: I CONFREQ [REQsent] id 40 len 10
Aug 24 13:12:55.294: As4 IPCP: Address 10.60.0.1 (0x03060A3C0001)
Aug 24 13:12:55.294: As4 IPCP: O CONFNAK [REQsent] id 40 len 10
Aug 24 13:12:55.298: As4 IPCP: Address 2.0.0.0 (0x030602000000)
Aug 24 13:12:55.526: As4 IPCP: I CONFACK [REQsent] id 102 len 10
Aug 24 13:12:55.530: As4 IPCP: Address 10.60.0.2 (0x03060A3C0002)
Aug 24 13:12:55.530: As4 IPCP: I CONFREQ [ACKrcvd] id 41 len 4
Aug 24 13:12:55.534: As4 IPCP: O CONFACK [ACKrcvd] id 41 len 4
Aug 24 13:12:55.538: As4 IPCP: State is Open
Aug 24 13:12:56.290: dialer Protocol up for As4
Aug 24 13:12:56.294: As4 IPCP: Remove route to 10.60.0.1
Aug 24 18:12:56.334: %LINEPROTO-5-UPDOWN: Line protocol on Interface Async4,
cha
nged state to up
Aug 24 13:12:56.358: As4 IPCP: Install route to 2.0.0.0
regards,
khalid
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:24:29 GMT-3