From: William Swedberg (swedbergwp@xxxxxxxxx)
Date: Tue Aug 08 2000 - 09:57:41 GMT-3
Can you post the configs.
Thanks
Bill Swedberg CCNP CCDP
--- Varghese Thomas <vnthomas@hotmail.com> wrote:
> hello
>
> those parameters are already in;but spoke 2 & 3
> never become active in
> appletalk. (their node number is showing as valid.)
>
> Any clue pls..
>
> Tx n Rd
>
>
> >From: "Tom Gonter" <tgonter@cisco.com>
> >Reply-To: "Tom Gonter" <tgonter@cisco.com>
> >To: "Varghese Thomas" <vnthomas@hotmail.com>,
> "'Ccielab"
> ><ccielab@groupstudy.com>
> >Subject: RE: Appletalk & EIGRP over a NBMA
> >Date: Mon, 7 Aug 2000 21:14:54 -0500
> >
> >You need to use no appletalk eigrp-splithorizon on
> your hub multipoint sub
> >interface. The split horizon you're using is for
> IP routing updates not
> >appletalk routing. Also note is you move to plain
> vanilla RTMP you'll need
> >no appletalk rtmp-splithorizon on the multipoint
> subinterface.
> >
> >See
> >
>
>http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/atip
> >x_c/2cdapple.htm#xtocid17069133
> > -----Original Message-----
> > From: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com]On Behalf Of
> >Varghese Thomas
> > Sent: Monday, August 07, 2000 5:10 PM
> > To: 'Ccielab
> > Subject: Appletalk & EIGRP over a NBMA
> >
> >
> > Hello,
> >
> > The set-up is 1 hub with 4 sopkes running EIGRAP
> in a FR cloud
> >
> > Hub has the following conf.
> >
> > no split horizon disabled
> > appletalk local routing
> >
> > Common settings in hub & sopke
> >
> > appletalk routing egirp XX (xx is uniuqe )
> >
> > network wan
> > appletalk protocol eigrp
> > no appletalk protocol rtmp
> > no frame-realy inver-arp
> >
> > In addition, all routers have proper PVC
> statements
> >
> > Issue:
> >
> > Hub(r1) & one of the spoke(4) works fine with
> their FR. AT. int comes
> >up.
> > sopke 2 & 3 never comes up in terms of AT int.
> Hub's cable/zone is
> >gettings verified by either r2 or r3 or even with
> r4(case by case) as well
> >as spoke 4 is also getting verified by rest of the
> routers.
> >
> > r2 & r3 shows "aquiring port net information",
> but never gets
> >established
> >and status of the resp. AT int is down.
> > I tried without EIGRP also, but the result is
> the same.
> >
> > Both spoke 2 &3 is running IOS 12.0(3)T3 and hub
> is 11.0(3) & spoke 4 is
> >12.0(1)
> >
> > Any hints pls?
> >
> > Tx n RD
>
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:24:22 GMT-3