From: William Swedberg (swedbergwp@xxxxxxxxx)
Date: Fri Jul 28 2000 - 09:43:49 GMT-3
Have you found a solution to the neighbor being in
init state? That's interesting output below. Have
you tried dropping the clock rate?
William Swedberg CCNP CCDP
--- Lawrence Dwyer <dwyer@tatrc.org> wrote:
> On my serial, at "clock rate ?"
> 8000000 is listed in the group, at the bottom it
> says
>
> ....
> 1000000
> 1300000
> 2000000
> 4000000
> 8000000
>
> <300-4000000> Choose clockrate from list above
>
> HTH
> Larry
>
> William Swedberg wrote:
>
> > I think I fell asleep at the wheel. The router
> would
> > not let you configure a rate higher then max for
> the
> > interface. If it let you do 8000000 then the
> > interface could do that. Try saving everything
> and
> > reboot. The ospf virtual-link connection can do
> funny
> > things.
> >
> > William Swedberg CCNP CCDP
> > --- Aaron DuShey <adushey@yahoo.com> wrote:
> > > I can't get r3-r4 to become adjacent. They are
> stuck
> > > in init? Any hints?
> > > ip tcp synwait-time 5
> > > no ip domain-lookup
> > > !
> > > !
> > > voice-port 1/0/0
> > > !
> > > voice-port 1/0/1
> > > !
> > > voice-port 1/1/0
> > > !
> > > voice-port 1/1/1
> > > !
> > > !
> > > interface Loopback0
> > > ip address 10.44.1.1 255.255.255.0
> > > !
> > > interface Loopback1
> > > ip address 10.44.2.1 255.255.255.0
> > > !
> > > interface BRI0/0
> > > no ip address
> > > shutdown
> > > !
> > > interface Ethernet0/0
> > > ip address 10.4.1.1 255.255.0.0
> > > no lat enabled
> > > !
> > > interface Serial0/0
> > > ip address 10.34.1.2 255.255.0.0
> > > no ip mroute-cache
> > > !
> > > interface TokenRing0/0
> > > no ip address
> > > shutdown
> > > ring-speed 16
> > > !
> > > router ospf 1
> > > network 10.4.0.0 0.0.255.255 area 3
> > > network 10.34.0.0 0.0.255.255 area 3
> > > network 10.44.0.0 0.0.255.255 area 44
> > > area 3 virtual-link 10.34.1.1
> > > area 44 range 10.44.0.0 255.255.0.0
> > > !
> > > ip classless
> > > logging buffered 4096 debugging
> > > !
> > > !
> > > line con 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > line aux 0
> > > line vty 0 4
> > > login
> > > !
> > > interface Ethernet0/0
> > > no ip address
> > > shutdown
> > > no lat enabled
> > > !
> > > interface Serial0/0
> > > ip address 10.10.1.3 255.255.0.0
> > > encapsulation frame-relay
> > > ip ospf priority 0
> > > no ip mroute-cache
> > > ip policy route-map frame
> > > no fair-queue
> > > frame-relay map ip 10.10.1.1 301 broadcast
> > > !
> > > interface TokenRing0/0
> > > ip address 10.3.1.1 255.255.0.0
> > > ring-speed 16
> > > !
> > > interface Serial0/1
> > > ip address 10.34.1.1 255.255.0.0
> > > clockrate 8000000
> > > !
> > > interface FastEthernet1/0
> > > no ip address
> > > shutdown
> > > no lat enabled
> > > !
> > > router ospf 1
> > > network 10.10.1.0 0.0.0.255 area 0
> > > network 10.34.0.0 0.0.255.255 area 3
> > > area 3 virtual-link 10.44.2.1
> > > ospf log-adjacency-changes
> > > !
> > > ip local policy route-map frame
> > > ip classless
> > > logging buffered 4096 debugging
> > > access-list 100 deny ip any 10.3.0.0 0.0.255.255
> > > access-list 100 deny ip any 10.34.0.0
> 0.0.255.255
> > > access-list 100 deny ip any 10.44.0.0
> 0.0.255.255
> > > access-list 100 deny ip any 10.4.0.0 0.0.255.255
> > > access-list 100 permit ip any any
> > > route-map frame permit 10
> > > match ip address 100
> > > set ip next-hop 10.10.1.1
> > > !
> > > !
> > > !
> > > line con 0
> > > exec-timeout 0 0
> > > logging synchronous
> > > line aux 0
> > > line vty 0 4
> > > login
> > > !
> > > end
> > > r3#
> > > end
> > > r3#sh ip ospf neig
> > > Neighbor ID Pri State Dead Time Address
> Interface
> > > 10.10.1.1 1 FULL/DR 00:01:52 10.10.1.1 Serial0/0
> > > 10.44.2.1 1 INIT/ - 00:00:37 10.34.1.2 Serial0/1
> > > r3#
> > > thanks
> > > ad
> > >
> > >
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:23:59 GMT-3