From: CHIDI FRANCIS (eejiofor@xxxxxxxxx)
Date: Sat Jul 08 2000 - 04:48:09 GMT-3
I am sorry I have been able to thank all members of this group for their
suggestions till now. I had to load a new code to the router and finally
changed the config-register to 0x2102 and I was back in business again.
Infact that was my last option and I had to so that I can move on with my
practice labs My LAb date is almost near.Thanks members
--- Nnanna Obuba <obuba@bellatlantic.net> wrote:
> Download teraterm pro ...I think the problem here is with hyperterminal
>
> cheers
>
> Nnanna
>
> ----- Original Message -----
> From: "CHIDI FRANCIS" <eejiofor@yahoo.com>
> To: <>
> Sent: Tuesday, July 04, 2000 11:37 PM
> Subject: Re: Console problem
>
>
> > Members, thanks for the advice. I have tried all suggested solutions, but
> no
> > luck. This is obviously a strange problem to me. Router still do no
> respond
> > to any keystrokes at all. Below is the output when I reloaded router
> >
> > Cisco Internetwork Operating System Software
> > IOS (tm) 2500 Software (C2500-D-L), Version 12.0(8), RELEASE SOFTWARE
> (fc1)
> > Copyright (c) 1986-1999 by cisco Systems, Inc.
> > Compiled Mon 29-Nov-99 14:24 by kpma
> > Image text-base: 0x030386CC, data-base: 0x00001000
> >
> > cisco 2509 (68030) processor (revision D) with 8192K/2048K bytes of
> memory.
> > Processor board ID 05228981, with hardware revision 00000000
> > Bridging software.
> > X.25 software, Version 3.0.0.
> > 1 Ethernet/IEEE 802.3 interface(s)
> > 2 Serial network interface(s)
> > 8 terminal line(s)
> > 32K bytes of non-volatile configuration memory.
> > 16384K bytes of processor board System flash (Read ONLY)
> >
> > This is as far as I can go. No router> or router# prompt at all. No
> response
> > from the router with the keystrokes. Any advice is welcomed. Thanks
> members
> >
> > --- Charles <mfortune@home.com> wrote:
> > > I had seen something close to this a while back. The only thing that I
> > > could
> > > find wrong was that the config-register was somehow changed. I had to
> break
> > > into the router as if I were doing password recovery and change the
> > > config-register back to 0x2102 and reload. This solved the problem that
> I
> > > was having. Also, see if you can get in through your aux port. I have
> had
> > > other lab partners shut down my console port in the past just as a
> prank.
> > > If
> > > you are the only one on the box this is probably not the case.
> > >
> > >
> > > ----- Original Message -----
> > > From: CHIDI FRANCIS <eejiofor@yahoo.com>
> > > To: <>
> > > Sent: Tuesday, July 04, 2000 12:41 PM
> > > Subject: Console problem
> > >
> > >
> > > > I need help so bad. I have 2509 connected to my pc through the
> console
> > > port
> > > > and to other 7 routers through an octal cable. Never had any problem
> till
> > > > yesterday when I cannot access the router through the connsole port.
> > > > Consequently, I do not have access to the other 7 routers. Have any
> > > member
> > > > had this problem before. I have checked and cross checked literally
> every
> > > > things and it looks ok. I have tried connecting same cable to another
> > > router
> > > > and it works fine--it accepts command from the key board, however,
> when I
> > > > connect to to this problem router it doesn't not accept commands from
> key
> > > > board. I have tried reload, I can see the output but router does not
> > > accept
> > > > command from the key board. My last effort was to issue a break key
> and
> > > then
> > > > to > prompt, that works because the router did accept commands typed.
> > > When
> > > I
> > > > reload and issue and command or enen hit my ENTER key, no response
> from
> > > the
> > > > router. Is this router in comma or dead forever, Any help will be
> highly
> > > > appreciated.
> > > >
> > > > CHi
> > > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:23:53 GMT-3