From: Kinton Connelly (kinton@xxxxxxxxxxxx)
Date: Wed May 03 2000 - 18:32:43 GMT-3
Unless one of the other people on the list has a better idea or has seen
this problem before, I'd look at loading 11.2 or 11.3 - hopefully the
routers will have enough memory for those versions. I just tried the "area
4 ?" command on an 11.2-14 router and it returned the same results as my
12.0 box.
Good luck,
Kinton
At 5/3/00, you wrote:
>Yep I'm sure -
>
>Got the full list you have below - except for the nssa option. 11.1.24
>should be "prime-time" enough where this should not be an issue. Can't
>load 12 because the router's don't have enough memory (Suppose I could load
>12 IP only.). They are at the local Cisco shop which is free so I am not
>about to complain about lack of memory
>
>Showed one of the local CCIE's and he was mistified as well.
>
>Any other ideas?
>
>Dana
>
>
>
>
>Kinton Connelly <kinton@oldmedia.com> on 05/03/2000 03:17:36 PM
>
>To: Dana_L_Steffey@notes.Seagate.COM, ccielab@groupstudy.com
>cc:
>
>Subject: Re: NSSA Question
>
>
>Did you get any other options when you pressed "?" ? I just tried it on my
>12.0(9) router and got this:
>
>r4(config-router)#area 10 ?
> authentication Enable authentication
> default-cost Set the summary default-cost of a NSSA/stub area
> nssa Specify a NSSA area
> range Summarize routes matching address/mask (border routers
>only)
> stub Specify a stub area
> virtual-link Define a virtual link and its parameters
>
>Were you for sure at the "config-router" prompt? I can't count the number
>of times I've typed "route rospf 1" and get a couple of network commands
>typed in before I notice my typo.
>
>Kinton
>
>At 5/3/00, you wrote:
> >Have a quick question on OSPF - I was trying to setup an area as NSSA on
> >one of the CCIE bootcamp labs and could not -
> >I am running 11.1.24 (mixture of enterprise, desktop, and ip/ipx) on 7 -
> >4700's
> >
> >Lab asked to setup area 4 as NSSA - So I went and typed
> >
> >router ospf 1
> >area 4 - (NSSA is suppose to be an option, but was not their)
> >
> >I then looked at the answer and sure enough it is supposed to be "area 4
> >NSSA"
> >
> >router ospf 1 (From the CCIEbootcamp answers)
> > redistribute eigrp 1 metric 20 metric-type 1 subnets
> > network 11.1.1.6 0.0.0.0 area 4
> > area 4 authentication
> > area 4 nssa
> > area 4 default-cost 20
> >
> >Anyone have any ideas on why NSSA would not be a choice when I tried it
>???
> >
> >Thanks,
> >
> >Dana Steffey, CCNP, CCDP, CCNA WAN Switching, MCSE, MCT, CNA, Electrical
> >Engineer
> >Lab: June 21st Halifax
> >Seagate Technology
> >Minneapolis, MN
> >
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:23:27 GMT-3