From: Joel W. Ekis (jekis@xxxxxxxxx)
Date: Mon Feb 14 2000 - 17:44:41 GMT-3
You just learned a very valuable CCIE Lab lesson. AppleTalk is the worst proto
col to deal with in the lab. Any time you make changes, you are almost require
d to reboot all the routers to get it to work. This is really bad when you hav
e 2500 routers which boot slow. Nothing is worse than sitting in the lab waiti
ng for the routers to reload, just to see if your configuration is going to wor
k this time.
Joel
At 10:45 PM 2/14/2000 -0800, Khurram Khani wrote:
>I rebooted all the 3 routers and it works ????? Save me.!
>
>----- Original Message -----
>From: Khurram Khani <ajmal@emirates.net.ae>
>To: <ccielab@groupstudy.com>
>Sent: Monday, February 14, 2000 9:25 PM
>Subject: Appletalk on NBMA
>
>
>> Hello.
>>
>> Problem, I am not getting Router 1 Ethernet 0 route advertisment in
>> Router2 and Router 3. Router 1 is advertsing cable-range 1-10 on
>> Framerelay cloud but other Routers not receiving it ??
>>
>> Router 2 ---> HUB (I have put 'no appletalk eigrp-splithorizon and
>> 'appletalk local-routing' instruction)
>>
>> Router 1 ---> Spoke
>> Router 3 ---> Spoke
>>
>>
>> Router 1 has one "eth 0" and one se2.1 point-to-point
>> Router 2 has one "eth 0" and one se2.1 multipoint
>> Router 3 has one "eth 0" and one se2.1 point-to-point
>>
>>
>> Configurations
>> ----
>>
>> router 1
>>
>> appletalk routing eigrp 2
>> appletalk route-redistribution
>> appletalk local-routing
>>
>> int eth 0
>> appletalk cable-range 1-10 1.1
>> appletalk zone Router1Ethernet
>> no shut
>>
>> int se2.1 point-to-point
>> appletalk cable-range 100-100 100.2
>> appletalk zone FrameRelay
>> appletalk protocol ei
>> no appletalk protocol rtmp
>>
>>
>> Router 2
>> ----------
>>
>> appletalk routing eigrp 1
>> appletalk route-redistribution
>> appletalk local-routing
>>
>> int eth 0
>> appletalk cable-range 11-20 11.1
>> appletalk zone Router2Ethernet
>> no shut
>>
>> int se2.1 multipoint
>> appletalk cable-range 100-100 100.1
>> appletalk zone FrameRelay
>> frame-relay map apple 100.2 101 bro
>> frame-relay map apple 100.3 104 bro
>> appletalk protocol ei
>> no appletalk protocol rtmp
>> no appletalk eigrp-splithorizon
>>
>> Router 3
>> --------
>> appletalk routing eigrp 3
>> appletalk route-redistribution
>> appletalk local-routing
>>
>> int eth 0
>> appletalk cable-range 30-30 30.1
>> appletalk zone Router3Ethernet
>> no shut
>>
>> int se2.1 point-to-point
>> appletalk cable-range 100-100 100.3
>> appletalk zone FrameRelay
>> appletalk protocol ei
>> no appletalk protocol rtmp
>>
>>
>>
>>
>>
>>
>> router1#
>> router1#
>>
>> (Notice 1-10 is advertised on Se2.1 but other routers are not receving it)
>> ---
>>
>> 02:44:42: AT: atigrp2_advertise_request, advertising 1-10 out Serial2.1
>>
>> 02:44:42: AT: atigrp2_advertise_request, advertising 100-100 out Serial2.1
>> 02:44:44: AT: atigrp2_advertise_request, advertising 1-10 out Serial2.1
>> 02:44:44: AT: atigrp2_advertise_request, advertising 100-100 out Serial2.1
>> 02:44:47: AT: atigrp2_rtdelete, deleting 100-100 from 100.1 on Serial2.1
>> 02:44:47: AT: atigrp2_rtupdate, metric 23284736 succ 1 for 100-100, is:
>> 100.1, n
>> h: 100.1, idb: Serial2.1
>> 02:44:47: AT: atigrp2_rtdelete, deleting 30-30 from 100.1 on Serial2.1
>> 02:44:47: AT: atigrp2_rtupdate, metric 23310336 succ 0 for 30-30, is:
>100.1,
>> nh:
>> 100.1, idb: Serial2.1
>> 02:44:47: AT: atigrp2_advertise_request, advertising 1-10 out Serial2.1
>> 02:44:47: AT: atigrp2_advertise_request, advertising 100-100 out Serial2.1
>>
>>
>>
>> router2(config)#end
>> router2#
>> 02:51:19: %SYS-5-CONFIG_I: Configured from console by console
>> router2#sh apple ro
>> Codes: R - RTMP derived, E - EIGRP derived, C - connected, A - AURP
>> S - static P - proxy
>> 3 routes in internet
>>
>> The first zone listed for each entry is its default (primary) zone.
>>
>> C Net 11-20 directly connected, Ethernet0, zone Router2Ethernet
>> E Net 30-30 [1/G] via 100.3, 1171 sec, Serial2.1, zone Router3Ethernet
>> C Net 100-100 directly connected, Serial2.1, zone FrameRelay
>> router2#
>>
>> router3#
>> router3#sh apple ro
>> Codes: R - RTMP derived, E - EIGRP derived, C - connected, A - AURP
>> S - static P - proxy
>> 3 routes in internet
>>
>> The first zone listed for each entry is its default (primary) zone.
>>
>> E Net 11-20 [1/G] via 100.1, 1185 sec, Serial2.1, zone Router2Ethernet
>> C Net 30-30 directly connected, Ethernet0, zone Router3Ethernet
>> C Net 100-100 directly connected, Serial2.1, zone FrameRelay
>> router3#
>>
>>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:22:53 GMT-3