From: Mark Olson (molson@xxxxxxxxxx)
Date: Mon Nov 08 1999 - 12:07:55 GMT-3
..... and don't forget about the 26xx, 36xx series. The console on those
beasts can go all the way up to 115200. If you get into rommon, just
issue the confreg command. It will take you through a series of questions,
one of which is the console port speed setting.
Scott Morris wrote:
> It's part of the config-register set... Out of the 16 bits that represent
> the config-register (like 0x2142), bits 11 and 12 represent the console
> speed.
>
> There are four possible settings on 25xx and 4xxx routers. They are 1200,
> 2400, 4800 and 9600.
>
> Bits 11/12 Speed
>
> 0 0 9600
> 0 1 4800
> 1 0 1200
> 1 1 2400
>
> This means that the overall register can be a pain in the ass to decode
> since those bits fall in two separate digits.
>
> Assuming that you want config-register to be 0x2142 for normal operation.
>
> If it's 0x2142 you're at 9600.
> 0x2942 is 4800
> 0x3142 is 1200
> 0x3942 is 2400
>
> Enjoy! But remember you will have figured out what speed it's at already
> (unless you telnet in), but 0x2142 will get you back where you want to
> be....
>
> Scott
>
> -----Original Message-----
> From: Brian Van Benschoten [mailto:vader@inxpress.net]
> Sent: Sunday, November 07, 1999 2:41 PM
> To: ccielab@groupstudy.com
> Subject: Re: Recover from console port speed change
>
> I see you point. There is only like 4 speeds it can be. However , if they
> change the speed you need to be able to change it back.
>
> I know I saw a list somewhere that explained what each of the bits did. I
> just cant remember where I saw it.
> ----- Original Message -----
> From: Scott Morris <SMorris@tele-tech.com>
> To: 'Brian Van Benschoten' <vader@inxpress.net>; <ccielab@groupstudy.com>
> Sent: Sunday, November 07, 1999 12:53 PM
> Subject: RE: Recover from console port speed change
>
> > Ok. Apparantly you're at that "stressing out" point... Simple.
> Remember,
> > simple. Do not overthink things....
> >
> > There aren't that many possible settings for console port speeds anyway...
> > Change your terminal program until you find the one that works. ;)
> >
> > Remember, just because you're going to be a CCIE does not mean that
> > everything in life is difficult or complex. Always remember the simple
> > solutions.
> >
> > Enjoy, and good luck!!!
> >
> > Scott Morris, MCSE, CNE (3.x), CCDP, CCIE #4713, Security
> > Specialization(CCIE)
> > smorris@tele-tech.com
> >
> >
> > -----Original Message-----
> > From: Brian Van Benschoten [mailto:vader@inxpress.net]
> > Sent: Sunday, November 07, 1999 1:06 PM
> > To: ccielab@groupstudy.com
> > Subject: Recover from console port speed change
> >
> >
> > Anyone know how to recover from a changed console port speed?
> >
> > Its one of the config registers, I can't seem to find a complete listing
> of
> > config-registers on CCO. I can find the bits needed to recover passwords
> > and boot ROM. Just not the console speed.
> >
> > Thanks.
> >
> > 3 days.....
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:21:55 GMT-3