From: Mark Detrick (mdetrick@xxxxxxxxx)
Date: Wed Sep 29 1999 - 16:20:19 GMT-3
Chad,
Well... I still stick to my original answer when using dialer pools. Maybe it
just wasn't clear which one you were
using and I made the assumption you were using dialer pools. Any luck with the
dialer pools?
Mark Detrick
Chad Marsh wrote:
>
> Mark Detrick wrote:
> >
> > No.
> >
>
> Hmmm... maybe you should have said: 'I don't believe so' to cover
> yourself, in case you were wrong, which you were. ;-)
>
> It appears that the 'dialer in-band' and 'dialer remote-name' commands
> are mutually exclusive on the Dialer interface.
> I have this working with rotary-groups, not sure if it would work with
> dialer pools, maybe I'll try that next.
> But the bottom line is that it DOES work.
> I just got it working, here are some relevant outputs and portions of
> the configs:
>
> Chad Marsh
>
> R5#sho snap
> Dialer1 is up, line protocol is upSnapshot client
> Options: dialer support
> Length of active period: 5 minutes
> Length of quiet period: 8 minutes
> Length of retry period: 8 minutes
> For dialer address 1
> Current state: active, remaining/exchange time: 4/2 minutes
> Connected dialer interface:
> BRI0:1
> Updates received this cycle: ip
>
> R6#sho snap
> Dialer1 is up, line protocol is upSnapshot server
> Options: dialer support
> Length of active period: 5 minutes
> For ip address: 172.16.1.5
> Current state: active, remaining time: 3 minutes
> Connected dialer interface:
> BRI0:1
>
> R5#sh ru
> Building configuration...
>
> Current configuration:
> !
> hostname R5
> !
> !
> username R6 password 0 ccie
> isdn switch-type basic-dms100
> !
> interface Loopback0
> ip address 10.5.1.1 255.255.255.0
> !
> interface BRI0
> no ip address
> encapsulation ppp
> isdn spid1 20649906240101 4990624
> isdn spid2 20649906250101 4990625
> dialer rotary-group 1
> no cdp enable
> !
> interface Dialer1
> ip address 172.16.1.5 255.255.255.0
> encapsulation ppp
> dialer in-band
> dialer in-band
> dialer map snapshot 1 4990622
> dialer map ip 172.16.1.6 name R6 broadcast 4990622
> dialer-group 1
> snapshot client 5 8 dialer
> no cdp enable
> ppp authentication chap
> !
> router rip
> network 10.0.0.0
> network 172.16.0.0
> !
> ip classless
> !
> dialer-list 1 protocol ip permit
> !
> R5#
>
> R6#sho run
> Building configuration...
>
> Current configuration:
> !
> hostname R6
> !
> !
> username R5 password 0 ccie
> isdn switch-type basic-dms100
> !
> interface Loopback0
> ip address 20.6.1.1 255.255.255.0
> !
> interface BRI0
> no ip address
> encapsulation ppp
> isdn spid1 20649906220101 4990622
> isdn spid2 20649906230101 4990623
> dialer rotary-group 1
> no cdp enable
> !
> interface Dialer1
> ip address 172.16.1.6 255.255.255.0
> encapsulation ppp
> dialer in-band
> dialer idle-timeout 30
> dialer map ip 172.16.1.5 name R5 broadcast 4990624
> dialer-group 1
> snapshot server 5 dialer
> no cdp enable
> ppp authentication chap
> !
> router rip
> network 10.0.0.0
> network 172.16.0.0
> !
> ip classless
> !
> dialer-list 1 protocol ip permit
> !
> R6#
-- Mark S. Detrick Cisco Systems QA Engineer Irvine, CA 92612
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:21:51 GMT-3