From: Chuah Eng Wee (chuahew@xxxxxxxxxxxxxxx)
Date: Thu Apr 08 1999 - 21:11:19 GMT-3
I have tried it using the neighbor command. If u don't specify it, the
router will
set it to one by default. Even if u set it to 10, it'll still go back to 1
!!!
I will try to upgrade the IOS to see if there is a bug .
Rgds
Eng Wee
At 17:27 08/04/99 -0400, Joe Soricelli wrote:
>Actually, I believe that everybody is right in this regard. There are two
>different places that you can specify a priority.
>
>In broadcast types networks, the default OSPF priority is 1, as some folks
>have said. To change it, you type the interface command "ip ospf priority".
>
>Router(config-router)#int e0/0
>Router(config-if)#ip ospf pri
>Router(config-if)#ip ospf priority ?
> <0-255> Priority
>
>However, for non-broadcast networks where you have to specify an OSPF
>neighbor (as in the original example), it is different. There is a separate
>priority statement for that under the neighbor command. Its default
>priority is 0.
>
>Router(config)#router ospf 1
>Router(config-router)#neigh 1.1.1.1 ?
> poll-interval OSPF dead-router polling interval
> priority OSPF priority of non-broadcast neighbor
> <cr>
>
>Router(config-router)#neigh 1.1.1.1 priority ?
> <0-255> Priority
>
>Hope this helps,
>Joe
>-----Original Message-----
>From: Rudy Phen <rudy.phen@datacraft-asia.com>
>To: Chuah Eng Wee <chuahew@cyberway.com.sg>; ccielab@groupstudy.com
><ccielab@groupstudy.com>
>Date: Wednesday, April 07, 1999 10:39 PM
>Subject: re: neighbor command
>
>
>>Hi Eng wee,
>>
>>regarding the priority issue, in cisco ios the default priority is 1,
>that's mean if you didn't configure priority, cisco router will have
>priority value is 1.
>>To change the priority for DR/BDR election, you must use "IP OSPF PRIORITY"
>interface command and put the command in the interface.
>>You may try it.. good luck
>>
>>Rudy Phen
>>Datacraft STARtrac
>>Phone : (65) 8436101
>>Fax : (65) 8420311
>>Email : rudy.phen@datacraft-asia.com
>>URL : http://www.datacraft-asia.com
>>
>>---------- Original Text ----------
>>
>>From: "Chuah Eng Wee" <chuahew@cyberway.com.sg>, on 07/04/1999 12:18 AM:
>>
>>Hi all,
>>
>>I have 3 routers in an NBMA network.
>>
>>The hub router uses point-to-point subinterface
>>Two spoke router use physical interface
>>
>>I want to make the hub router a DR, therefore, at the hub router, i use
>>
>>router ospf 10
>> network ......
>> neighbor spokeA-ip
>> neighbor spkeB-ip
>>
>>At spokeA,
>>router ospf 10
>> neigh Hub-ip priority 10
>>
>>At spokeB,
>> neigh Hub-ip priority 10
>>
>>I read from the documentation that if no priority is not specified, it'll
>>be priority 0,
>>which implies it will not participate in DB/BRD election. However, I get a
>>priority of 1
>>when I did not specify it. At the spoke, the configuration will change the
>>priority to 1
>>after a while even when I keyed in the priority to be 10.
>>
>>Any idea what did I miss out or there's bug in the IOS ??
>>
>>Thanks
>>Eng Wee
>>
>>
>>
>>
>>
>>
>>
>
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:21:36 GMT-3