Re: OT: Logical Bundle

Imagine that there is no configuration, as it does not matter. Because the
restriction is only on the physical topology.
Assume that we are going to configure the following static route on both of
Cisco routers:
ip route 10.10.1.0 255.255.255.0 192.168.1.1
And 192.168.1.1 is a logical IP which is on both of Huawei devices.
and the same for reverse of the scenario.
I've tried VRRP, but I failed to success. It seems to me that all the links
should be placed on the same subnet.... but how?
Would you please guide me through it?
I mean for example how should H1 reach the virtual address of Cisco routers
if its link to C1 is not available?
C1---x----H1-------
 | | |
 | | 10.10.1.0
 | | |
C2--------H2--------

On Thu, May 16, 2013 at 7:57 PM, Paul Cocker <groupstudy_at_paulcocker.net>wrote:

> VRRP....
>
>
> On 16 May 2013 15:11, Mohammad Moghaddas <moghaddas.it_at_gmail.com> wrote:
>
>> Let me clarify more about the issue.
>> For example, C1 or C2 could ping 200.200.200.200 and H1 or H2 should
>> respond the icmp message, and whenever one of them is unavailable, the
>> other one should handle the response.
>>
>>
>> On Thu, May 16, 2013 at 5:57 PM, Tony Singh <mothafungla_at_gmail.com>
>> wrote:
>>
>> > POS is point to point, how do the routers know of each others subnets?
>> > Dynamic routing or they sharing a /30 Cisco-Huawei
>> >
>> > --
>> > BR
>> >
>> > Sent from my iPhone on 3
>> >
>> > On 16 May 2013, at 14:19, Mohammad Moghaddas <moghaddas.it_at_gmail.com>
>> > wrote:
>> >
>> > Yes, VRRP is supported.
>> >
>> >
>> > On Thu, May 16, 2013 at 4:40 PM, Tony Singh <mothafungla_at_gmail.com>
>> wrote:
>> >
>> >> does Huawei support VRRP? They prob do HSRP :p
>> >>
>> >> --
>> >> BR
>> >>
>> >> Tony
>> >>
>> >> Sent from my iPhone on 3
>> >>
>> >> On 16 May 2013, at 13:07, Mohammad Moghaddas <moghaddas.it_at_gmail.com>
>> >> wrote:
>> >>
>> >> > Hi.
>> >> >
>> >> > Sorry for the OT.
>> >> > I was not sure of what to use as the subject of this OT.
>> >> > There are 2 * 7613 and 2 Huawei routers connected as below:
>> >> > C1--------H1
>> >> > | |
>> >> > | |
>> >> > C2--------H2
>> >> >
>> >> > All the connected ports are POS (STM1).
>> >> > We need that Huawei routers see Cisco routers as using 1 IP address,
>> >> Cisco
>> >> > routers see Huawei routers using 1 IP address.
>> >> > We can't add any link and make the topology a full-mesh one.
>> >> > I have thoughts of some L2 solutions using VLANs, but I would
>> >> appreciate to
>> >> > hear any solutions from you guys.
>> >> >
>> >> > Thanks.
>> >> >
>> >> >
>> >> > Blogs and organic groups at http://www.ccie.net
>> >> >
>> >> >
>> _______________________________________________________________________
>> >> > Subscription information may be found at:
>> >> > http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Fri May 17 2013 - 01:45:02 ART