Re: Router on a stick question

Well then the output may have been correct. If the ports are blocking they
obviously aren't going to forward any traffic.

On Fri, Mar 15, 2013 at 6:18 PM, Maneesh Chawla <coolmaneesh_at_gmail.com>wrote:

> Ohh, thanks for the feedback Marc !! Greatly helps to know.
>
> I initially thought that the output was correct cos spanning-tree output
> showed 2/1 and 2/2 in blocking state.
>
>
>
> On Fri, Mar 15, 2013 at 3:26 PM, marc abel <marcabel_at_gmail.com> wrote:
>
>> This is what I am talking about:
>>
>> This part shows you what is allowed over the trunk:
>>
>> Port Vlans allowed and active in management domain
>> Et2/0 1,67,79,100
>> Et2/1 1,67,79,100
>> Et2/2 1,67,79,100
>> Et3/0 1,67,79,100
>> Et3/1 1,67,79,100
>> Et3/2 1,67,79,100
>> Et4/0 1,67,79,100
>> Et4/1 1,67,79,100
>> Et4/2 1,67,79,100
>>
>> This part shows you what is actually being sent over the trunk. For this
>> part the entry for Et2/0, 4/0, 4/1, and 4/2 are what you would want to see.
>> Your VLANs are being sent. The entries for E2/1 - 3/2 aren't sending any
>> VLANs over the trunk. Usually this is going to only happen if you have VLAN
>> pruning turned on or if the interface is in Spanning-tree blocking state
>> for those VLANS.
>>
>> Port Vlans in spanning tree forwarding state and not pruned
>> Et2/0 1,67,79,100
>> Et2/1 none
>> Et2/2 none
>> Et3/0 none
>> Et3/1 none
>> Et3/2 none
>> Et4/0 1,67,79,100
>> Et4/1 1,67,79,100
>> Et4/2 1,67,79,100
>>
>> Like I said IOU does some strange things, especially around layer 2
>> stuff. One thing that threw me for a loop in the troubleshooting lab is
>> that the result of "show run | sec bgp" would only show me part of the BGP
>> configuration. Leaving out part of the config so I had to start using "show
>> run | beg router bgp" instead to see the bgp config.
>>
>> -Marc
>>
>>
>> On Fri, Mar 15, 2013 at 4:51 PM, Maneesh Chawla <coolmaneesh_at_gmail.com>wrote:
>>
>>> Thank Marc !!
>>> You are right that I am running IOU.
>>>
>>> I am still trying to understand which o/p.
>>>
>>> I thought the o/p was ok due to spanning-tree running on the links.
>>>
>>>
>>>
>>> On Fri, Mar 15, 2013 at 2:48 PM, marc abel <marcabel_at_gmail.com> wrote:
>>>
>>>> That seems like an artifact of running IOU. I noticed in your first
>>>> show int trunk that it showed there were no vlans it was forwarding for on
>>>> the trunks even though they were allowed. That is why I was asking about
>>>> spanning-tree, I think this is just likely a software glitch for you.
>>>>
>>>>
>>>> On Fri, Mar 15, 2013 at 4:36 PM, Maneesh Chawla <coolmaneesh_at_gmail.com>wrote:
>>>>
>>>>> Strange thing happened.
>>>>>
>>>>> I had below on sw1 :
>>>>>
>>>>> Rack1SW1#show interfa trunk
>>>>>
>>>>> Port Mode Encapsulation Status Native
>>>>> vlan
>>>>> Et2/0 desirable n-802.1q trunking 1
>>>>> Et2/1 desirable n-802.1q trunking 1
>>>>> Et2/2 desirable n-802.1q trunking 1
>>>>> Et3/0 desirable n-802.1q trunking 1
>>>>>
>>>>> <snipped from show run>
>>>>>
>>>>> !
>>>>> interface Ethernet2/0
>>>>> duplex auto
>>>>> !
>>>>> interface Ethernet2/1
>>>>> duplex auto
>>>>> !
>>>>> interface Ethernet2/2
>>>>> duplex auto
>>>>> !
>>>>>
>>>>>
>>>>>
>>>>> Now, made the below change and everything worked.
>>>>>
>>>>> Enter configuration commands, one per line. End with CNTL/Z.
>>>>> Rack1SW1(config)#interface range e2/0-2
>>>>> Rack1SW1(config-if-range)#switchport trunk encap dot1
>>>>> Rack1SW1(config-if-range)#switchport mode trunk
>>>>> Rack1SW1(config-if-range)#
>>>>>
>>>>>
>>>>>
>>>>> Can someone help me understand this ?
>>>>>
>>>>> Thanks
>>>>> Maneesh
>>>>>
>>>>> On Fri, Mar 15, 2013 at 2:24 PM, marc abel <marcabel_at_gmail.com> wrote:
>>>>>
>>>>>> Does VLAN 67 exist on Sw2?
>>>>>>
>>>>>> Please also provide show int trunk from SW2, as well as a show span
>>>>>> vlan 67 on Sw1/
>>>>>>
>>>>>>
>>>>>>
>>>>>> On Fri, Mar 15, 2013 at 3:58 PM, Kapil Atrish <
>>>>>> kapilatrish_at_hotmail.com> wrote:
>>>>>>
>>>>>>> Can you add int vlan 67 on Switch 2 as well and see which side is
>>>>>>> pingable
>>>>>>> from there? Perhaps, create the following int on SW2 and try to ping
>>>>>>> Router
>>>>>>> and SW1 both to get an idea which side is failing. SW2:
>>>>>>> interface Vlan67
>>>>>>> ip address 155.15.67.10 255.255.255.0
>>>>>>> Thanks,Kapil Also, > Date: Fri, 15 Mar 2013 10:54:32 -0700
>>>>>>> > Subject: Re: Router on a stick question
>>>>>>> > From: coolmaneesh_at_gmail.com
>>>>>>> > To: jb.poplawski_at_gmail.com
>>>>>>> > CC: ccielab_at_groupstudy.com
>>>>>>> >
>>>>>>> > Auto-negotiated
>>>>>>> >
>>>>>>> > Rack1SW1#show interface trunk
>>>>>>> >
>>>>>>> > Port Mode Encapsulation Status
>>>>>>> Native vlan
>>>>>>> > Et2/0 desirable n-802.1q trunking 1
>>>>>>> > Et2/1 desirable n-802.1q trunking 1
>>>>>>> > Et2/2 desirable n-802.1q trunking 1
>>>>>>> > Et3/0 desirable n-802.1q trunking 1
>>>>>>> > Et3/1 desirable n-802.1q trunking 1
>>>>>>> > Et3/2 desirable n-802.1q trunking 1
>>>>>>> > Et4/0 desirable n-isl trunking 1
>>>>>>> > Et4/1 desirable n-isl trunking 1
>>>>>>> > Et4/2 desirable n-isl trunking 1
>>>>>>> >
>>>>>>> > Port Vlans allowed on trunk
>>>>>>> > Et2/0 1-4094
>>>>>>> > Et2/1 1-4094
>>>>>>> > Et2/2 1-4094
>>>>>>> > Et3/0 1-4094
>>>>>>> > Et3/1 1-4094
>>>>>>> > Et3/2 1-4094
>>>>>>> > Et4/0 1-4094
>>>>>>> > Et4/1 1-4094
>>>>>>> > Et4/2 1-4094
>>>>>>> >
>>>>>>> > Port Vlans allowed and active in management domain
>>>>>>> > Et2/0 1,67,79,100
>>>>>>> > Et2/1 1,67,79,100
>>>>>>> > Et2/2 1,67,79,100
>>>>>>> > Et3/0 1,67,79,100
>>>>>>> > Et3/1 1,67,79,100
>>>>>>> > Et3/2 1,67,79,100
>>>>>>> > Et4/0 1,67,79,100
>>>>>>> > Et4/1 1,67,79,100
>>>>>>> > Et4/2 1,67,79,100
>>>>>>> >
>>>>>>> > Port Vlans in spanning tree forwarding state and
>>>>>>> not pruned
>>>>>>> > Et2/0 1,67,79,100
>>>>>>> > Et2/1 none
>>>>>>> > Et2/2 none
>>>>>>> > Et3/0 none
>>>>>>> > Et3/1 none
>>>>>>> > Et3/2 none
>>>>>>> > Et4/0 1,67,79,100
>>>>>>> > Et4/1 1,67,79,100
>>>>>>> > Et4/2 1,67,79,100
>>>>>>> >
>>>>>>> >
>>>>>>> > On Fri, Mar 15, 2013 at 10:51 AM, JB Poplawski
>>>>>>> <jb.poplawski_at_gmail.com>wrote:
>>>>>>> >
>>>>>>> > > Interface up on the switch? Is Switch A supposed to trunk
>>>>>>> somewhere, I
>>>>>>> > > don't see it.
>>>>>>> > >
>>>>>>> > >
>>>>>>> > > On Fri, Mar 15, 2013 at 12:46 PM, Maneesh Chawla
>>>>>>> <coolmaneesh_at_gmail.com>wrote:
>>>>>>> > >
>>>>>>> > >> Topo
>>>>>>> > >> -------
>>>>>>> > >>
>>>>>>> > >> .7 .6
>>>>>>> > >> SW1------------------------------R6
>>>>>>> > >>
>>>>>>> > >> (155.15.67.0/24 vlan 67)
>>>>>>> > >>
>>>>>>> > >>
>>>>>>> > >> Physical topo
>>>>>>> > >> --------------------
>>>>>>> > >>
>>>>>>> > >>
>>>>>>> > >>
>>>>>>>
>>>>>>> SW1-(e2/0-2)-------------------(e2/0-2)-SW2-(e1/2)-------------------(e0/0)-R
>>>>>>> 6
>>>>>>> > >>
>>>>>>> > >>
>>>>>>> > >> I have attached below the configs. The example is taken from
>>>>>>> INE videos
>>>>>>> > >> module 1 lesson 1.
>>>>>>> > >>
>>>>>>> > >> not able to ping from R6 to SW1.
>>>>>>> > >> Not sure what am I missing here. Can the gurus help out ?
>>>>>>> > >>
>>>>>>> > >> Attached the configs.
>>>>>>> > >> R6
>>>>>>> > >> -------
>>>>>>> > >>
>>>>>>> > >> Rack1R6#show run
>>>>>>> > >> Building configuration...
>>>>>>> > >>
>>>>>>> > >> Current configuration : 1414 bytes
>>>>>>> > >> !
>>>>>>> > >> ! Last configuration change at 18:19:48 CET Fri Mar 15 2013
>>>>>>> > >> !
>>>>>>> > >> version 12.4
>>>>>>> > >> service timestamps debug datetime msec
>>>>>>> > >> service timestamps log datetime msec
>>>>>>> > >> no service password-encryption
>>>>>>> > >> !
>>>>>>> > >> hostname Rack1R6
>>>>>>> > >> !
>>>>>>> > >> boot-start-marker
>>>>>>> > >> boot-end-marker
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> no aaa new-model
>>>>>>> > >> clock timezone CET 1
>>>>>>> > >> mmi polling-interval 60
>>>>>>> > >> no mmi auto-configure
>>>>>>> > >> no mmi pvc
>>>>>>> > >> mmi snmp-timeout 180
>>>>>>> > >> ip source-route
>>>>>>> > >> ip auth-proxy max-login-attempts 5
>>>>>>> > >> ip admission max-login-attempts 5
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> ip cef
>>>>>>> > >> no ip domain lookup
>>>>>>> > >> no ipv6 traffic interface-statistics
>>>>>>> > >> no ipv6 cef
>>>>>>> > >> !
>>>>>>> > >> multilink bundle-name authenticated
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> redundancy
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet0/0
>>>>>>> > >> no ip address
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet0/0.67
>>>>>>> > >> encapsulation dot1Q 67
>>>>>>> > >> ip address 155.15.67.6 255.255.255.0
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet0/1
>>>>>>> > >> no ip address
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet0/2
>>>>>>> > >> no ip address
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet0/3
>>>>>>> > >> no ip address
>>>>>>> > >> !
>>>>>>> > >> interface Serial1/0
>>>>>>> > >> no ip address
>>>>>>> > >> serial restart-delay 0
>>>>>>> > >> !
>>>>>>> > >> interface Serial1/1
>>>>>>> > >> no ip address
>>>>>>> > >> serial restart-delay 0
>>>>>>> > >> !
>>>>>>> > >> interface Serial1/2
>>>>>>> > >> no ip address
>>>>>>> > >> serial restart-delay 0
>>>>>>> > >> !
>>>>>>> > >> interface Serial1/3
>>>>>>> > >> no ip address
>>>>>>> > >> serial restart-delay 0
>>>>>>> > >> !
>>>>>>> > >> ip forward-protocol nd
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> no ip http server
>>>>>>> > >> no ip http secure-server
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> control-plane
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> line con 0
>>>>>>> > >> exec-timeout 0 0
>>>>>>> > >> privilege level 15
>>>>>>> > >> logging synchronous
>>>>>>> > >> line aux 0
>>>>>>> > >> exec-timeout 0 0
>>>>>>> > >> privilege level 15
>>>>>>> > >> line vty 0 4
>>>>>>> > >> login
>>>>>>> > >> transport input all
>>>>>>> > >> !
>>>>>>> > >> exception data-corruption buffer truncate
>>>>>>> > >> end
>>>>>>> > >>
>>>>>>> > >>
>>>>>>> > >>
>>>>>>> > >>
>>>>>>> > >> sw1
>>>>>>> > >> -------
>>>>>>> > >>
>>>>>>> > >>
>>>>>>> > >> Rack1SW1#show run
>>>>>>> > >> Building configuration...
>>>>>>> > >>
>>>>>>> > >> Current configuration : 1597 bytes
>>>>>>> > >> !
>>>>>>> > >> ! Last configuration change at 18:10:16 CET Fri Mar 15 2013
>>>>>>> > >> !
>>>>>>> > >> version 15.0
>>>>>>> > >> service timestamps debug datetime msec
>>>>>>> > >> service timestamps log datetime msec
>>>>>>> > >> no service password-encryption
>>>>>>> > >> !
>>>>>>> > >> hostname Rack1SW1
>>>>>>> > >> !
>>>>>>> > >> boot-start-marker
>>>>>>> > >> boot-end-marker
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> no aaa new-model
>>>>>>> > >> clock timezone CET 1
>>>>>>> > >> !
>>>>>>> > >> ip cef
>>>>>>> > >> no ip domain-lookup
>>>>>>> > >> !
>>>>>>> > >> no ipv6 cef
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> spanning-tree mode pvst
>>>>>>> > >> spanning-tree extend system-id
>>>>>>> > >> !
>>>>>>> > >> vlan internal allocation policy ascending
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet0/0
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet0/1
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet0/2
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet0/3
>>>>>>> > >> no switchport
>>>>>>> > >> ip address 155.15.37.7 255.255.255.0
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet1/0
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet1/1
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet1/2
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet1/3
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet2/0
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet2/1
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet2/2
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet2/3
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet3/0
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet3/1
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet3/2
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet3/3
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet4/0
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet4/1
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet4/2
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet4/3
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Vlan1
>>>>>>> > >> no ip address
>>>>>>> > >> shutdown
>>>>>>> > >> !
>>>>>>> > >> interface Vlan67
>>>>>>> > >> ip address 155.15.67.7 255.255.255.0
>>>>>>> > >> !
>>>>>>> > >> interface Vlan79
>>>>>>> > >> ip address 155.15.79.7 255.255.255.0
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> ip forward-protocol nd
>>>>>>> > >> no ip http server
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> control-plane
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> line con 0
>>>>>>> > >> exec-timeout 0 0
>>>>>>> > >> privilege level 15
>>>>>>> > >> logging synchronous
>>>>>>> > >> line aux 0
>>>>>>> > >> line vty 0 4
>>>>>>> > >> login
>>>>>>> > >> transport input all
>>>>>>> > >> !
>>>>>>> > >> end
>>>>>>> > >>
>>>>>>> > >>
>>>>>>> > >>
>>>>>>> > >> sw2
>>>>>>> > >> -------
>>>>>>> > >>
>>>>>>> > >> Rack1SW2#show run
>>>>>>> > >> Building configuration...
>>>>>>> > >>
>>>>>>> > >> Current configuration : 1674 bytes
>>>>>>> > >> !
>>>>>>> > >> ! Last configuration change at 17:35:16 CET Fri Mar 15 2013
>>>>>>> > >> !
>>>>>>> > >> version 15.0
>>>>>>> > >> service timestamps debug datetime msec
>>>>>>> > >> service timestamps log datetime msec
>>>>>>> > >> no service password-encryption
>>>>>>> > >> !
>>>>>>> > >> hostname Rack1SW2
>>>>>>> > >> !
>>>>>>> > >> boot-start-marker
>>>>>>> > >> boot-end-marker
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> no aaa new-model
>>>>>>> > >> clock timezone CET 1
>>>>>>> > >> !
>>>>>>> > >> ip cef
>>>>>>> > >> no ip domain-lookup
>>>>>>> > >> !
>>>>>>> > >> no ipv6 cef
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> spanning-tree mode pvst
>>>>>>> > >> spanning-tree extend system-id
>>>>>>> > >> !
>>>>>>> > >> vlan internal allocation policy ascending
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet0/0
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet0/1
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet0/2
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet0/3
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet1/0
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet1/1
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet1/2
>>>>>>> > >> switchport trunk encapsulation dot1q
>>>>>>> > >> switchport mode trunk
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet1/3
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet2/0
>>>>>>> > >> switchport trunk encapsulation dot1q
>>>>>>> > >> switchport mode trunk
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet2/1
>>>>>>> > >> switchport trunk encapsulation dot1q
>>>>>>> > >> switchport mode trunk
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet2/2
>>>>>>> > >> switchport trunk encapsulation dot1q
>>>>>>> > >> switchport mode trunk
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet2/3
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet3/0
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet3/1
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet3/2
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet3/3
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet4/0
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet4/1
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet4/2
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Ethernet4/3
>>>>>>> > >> duplex auto
>>>>>>> > >> !
>>>>>>> > >> interface Vlan1
>>>>>>> > >> no ip address
>>>>>>> > >> shutdown
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> ip forward-protocol nd
>>>>>>> > >> no ip http server
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> control-plane
>>>>>>> > >> !
>>>>>>> > >> !
>>>>>>> > >> line con 0
>>>>>>> > >> exec-timeout 0 0
>>>>>>> > >> privilege level 15
>>>>>>> > >> logging synchronous
>>>>>>> > >> line aux 0
>>>>>>> > >> line vty 0 4
>>>>>>> > >> login
>>>>>>> > >> transport input all
>>>>>>> > >> !
>>>>>>> > >> end
>>>>>>> > >>
>>>>>>> > >>
>>>>>>> > >> Blogs and organic groups at http://www.ccie.net
>>>>>>> > >>
>>>>>>> > >>
>>>>>>> _______________________________________________________________________
>>>>>>> > >> Subscription information may be found at:
>>>>>>> > >> http://www.groupstudy.com/list/CCIELab.html
>>>>>>> >
>>>>>>> >
>>>>>>> > Blogs and organic groups at http://www.ccie.net
>>>>>>> >
>>>>>>> >
>>>>>>> _______________________________________________________________________
>>>>>>> > Subscription information may be found at:
>>>>>>> > http://www.groupstudy.com/list/CCIELab.html
>>>>>>>
>>>>>>>
>>>>>>> Blogs and organic groups at http://www.ccie.net
>>>>>>>
>>>>>>>
>>>>>>> _______________________________________________________________________
>>>>>>> Subscription information may be found at:
>>>>>>> http://www.groupstudy.com/list/CCIELab.html
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>> Marc Abel
>>>>>> CCIE #35470
>>>>>> (Routing and Switching)
>>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>> --
>>>> Marc Abel
>>>> CCIE #35470
>>>> (Routing and Switching)
>>>>
>>>
>>>
>>
>>
>> --
>> Marc Abel
>> CCIE #35470
>> (Routing and Switching)
>>
>
>

-- 
Marc Abel
CCIE #35470
(Routing and Switching)
Blogs and organic groups at http://www.ccie.net