Re: OSPF on 32 bit dialer interface

Thnaks Mousa, I have removed the ip opsf mtu-ignore and ip osp netwo
commands from physical interfaces as well. still not working. I will do
more debugging and send the print.
Regards

On 28 November 2012 14:52, Mohammad Mousa <mohd-mousa_at_hotmail.com> wrote:

> Tauseef,
>
> I just finished the lab, It works fine, just remove the no peer
> neighbor-route and without any OSPF network type configuration.
>
> --
> Mohammad Mousa
> CCIE #36990
> On Nov 28, 2012, at 5:20 PM, Mohammad Mousa wrote:
>
> > Tauseef,
> >
> > Try to remove the no peer neighbor-route command, you configured the
> > virtual-template interface as /24 and you give the dialer side /32 host
> route.
> > When you remove the no peer neighbor command, you will install /32 host
> route
> > on each side. also as Joe said you don't have to configure ospf networks
> > type.
> >
> >
> > Try this and let me know what will happen.
> >
> >
> > --
> > Mohammad Mousa
> > CCIE 336990
> >
> >
> >
> >
> >
> >
> >
> > On Nov 28, 2012, at 2:24 PM, Tauseef Khan wrote:
> >
> >> sorry made a mistake in pasting
> >> ip local-pool 6.6 172.31.255.254
> >>
> >> !
> >> peer default ip address 6.6
> >>
> >> Regrads
> >>
> >> On 28 November 2012 11:22, Mohammad Mousa <mohd-mousa_at_hotmail.com>
> wrote:
> >> Before I lab it up, I noticed your pool name is different than of you've
> > called it.
> >>
> >>> nterface Virtual-Template16
> >>
> >>> peer default ip address pool 1.6
> >>
> >>
> >>> ip local-pool 6.6 172.31.255.254
> >>
> >> Did you receive ip address on the Dialer side?
> >>
> >> --
> >> Mohammad Mousa
> >> CCIE #36990
> >>
> >>
> >>
> >> On Nov 28, 2012, at 2:03 PM, Tauseef Khan wrote:
> >>
> >>> Please find below the configs
> >>> server:R1
> >>>
> >>> bba-group pppoe CISCO
> >>> virtual-template 16
> >>> !
> >>> interface Gigabit0/0
> >>> no ip address
> >>> ip ospf network point-to-multipoint
> >>> ip ospf mtu-ignore
> >>> duplex auto
> >>> speed auto
> >>> pppoe enable group CISCO
> >>> end
> >>>
> >>> !
> >>> interface Virtual-Template16
> >>> mtu 1492
> >>> ip address 172.31.255.1 255.255.255.0
> >>> ip ospf network point-to-multipoint
> >>> ip ospf mtu-ignore
> >>> peer default ip address pool 1.6
> >>> ppp authentication chap
> >>> end
> >>>
> >>> usename R2 password pass
> >>>
> >>> ip local-pool 6.6 172.31.255.254
> >>>
> >>> __________________________________________________
> >>>
> >>> Client R2:
> >>> interface FastEthernet0/0
> >>> no ip address
> >>> ip ospf network point-to-multipoint
> >>> ip ospf mtu-ignore
> >>> speed auto
> >>> half-duplex
> >>> pppoe enable
> >>> pppoe-client dial-pool-number 16
> >>> !
> >>>
> >>> interface Dialer16
> >>> mtu 1492
> >>> ip address negotiated
> >>> encapsulation ppp
> >>> ip ospf network point-to-multipoint
> >>> dialer pool 16
> >>> dialer idle-timeout 0
> >>> dialer persistent
> >>> no peer neighbor-route
> >>> ppp chap password 0 pass
> >>> end
> >>>
> >>> R2:
> >>> sh ip ospf int br
> >>> Interface PID Area IP Address/Mask Cost State Nbrs
> F/C
> >>>
> __________________________________________________________________________
> >>> Di16 1 2 172.31.255.254/32 1785 P2MP
> 0/0
> >>>
> __________________________________________________________________________
> >>>
> >>> Kind regards
> >>>
> >>> Tauseef
> >>> mobile: +44 7837209187
> >>>
> >>>
> >>> On 28 November 2012 10:10, Mohammad Mousa <mohd-mousa_at_hotmail.com>
> wrote:
> >>> Post your full configs so we can check together. Did you change the
> MTU?
> >>>
> >>> --
> >>> Mohammad Mousa
> >>> CCIE #36990
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>> On Nov 28, 2012, at 12:28 PM, Tauseef Khan wrote:
> >>>
> >>>> Appreciate if some one could help. I have ospf running on 2 routers
> R1
> > and
> >>>> R2.
> >>>> R2 is a PPPoE client and R1 is the server. R2 has a negotiated ip
> > address
> >>>> on the dialer interface from R1 which is host (/32) address while R1
> has
> > a
> >>>> /29 bit Ip address on its interface facing towards Client.
> >>>> OSPF adj is not coming up between the client and Server
> >>>> On client dialer int and Server int I have ip ospf network
> >>>> point-to-multipoint
> >>>> i also tried no peer neighbor-route on client dialer interface.
> >>>>
> >>>> debugs on the client side show:
> >>>> OSPF: Rcv pkt from 172.31.29.1, Dialer16, area 0.0.0.3 : src not on
> the
> >>>> same network
> >>>>
> >>>> I have tried changing the network type to poin-to-poitn as well but no
> > adj
> >>>>
> >>>> Regards
> >>>>
> >>>>
> >>>> Blogs and organic groups at http://www.ccie.net
> >>>>
> >>>>
> _______________________________________________________________________
> >>>> Subscription information may be found at:
> >>>> http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Wed Nov 28 2012 - 14:55:42 ART