Re: OSPF on 32 bit dialer interface

sorry made a mistake in pasting
ip local-pool 6.6 172.31.255.254

!
peer default ip address 6.6

Regrads

On 28 November 2012 11:22, Mohammad Mousa <mohd-mousa_at_hotmail.com> wrote:

> Before I lab it up, I noticed your pool name is different than of you've
> called it.
>
> nterface Virtual-Template16
>
> peer default ip address pool* 1.6*
>
>
> ip local-pool *6.6* 172.31.255.254
>
>
> Did you receive ip address on the Dialer side?
>
> --
> Mohammad Mousa
> CCIE #36990
>
>
>
> On Nov 28, 2012, at 2:03 PM, Tauseef Khan wrote:
>
> Please find below the configs
> server:R1
>
> bba-group pppoe CISCO
> virtual-template 16
> !
> interface Gigabit0/0
> no ip address
> ip ospf network point-to-multipoint
> ip ospf mtu-ignore
> duplex auto
> speed auto
> pppoe enable group CISCO
> end
>
> !
> interface Virtual-Template16
> mtu 1492
> ip address 172.31.255.1 255.255.255.0
> ip ospf network point-to-multipoint
> ip ospf mtu-ignore
> peer default ip address pool 1.6
> ppp authentication chap
> end
>
> usename R2 password pass
>
> ip local-pool 6.6 172.31.255.254
>
> __________________________________________________
>
> Client R2:
> interface FastEthernet0/0
> no ip address
> ip ospf network point-to-multipoint
> ip ospf mtu-ignore
> speed auto
> half-duplex
> pppoe enable
> pppoe-client dial-pool-number 16
> !
>
> interface Dialer16
> mtu 1492
> ip address negotiated
> encapsulation ppp
> ip ospf network point-to-multipoint
> dialer pool 16
> dialer idle-timeout 0
> dialer persistent
> no peer neighbor-route
> ppp chap password 0 pass
> end
>
> R2:
> sh ip ospf int br
> Interface PID Area IP Address/Mask Cost State Nbrs F/C
> __________________________________________________________________________
> Di16 1 2 172.31.255.254/32 1785 P2MP 0/0
> __________________________________________________________________________
>
> Kind regards
>
> Tauseef
> mobile: +44 7837209187
>
>
> On 28 November 2012 10:10, Mohammad Mousa <mohd-mousa_at_hotmail.com> wrote:
>
>> Post your full configs so we can check together. Did you change the MTU?
>>
>> --
>> Mohammad Mousa
>> CCIE #36990
>>
>>
>>
>>
>>
>>
>> On Nov 28, 2012, at 12:28 PM, Tauseef Khan wrote:
>>
>> > Appreciate if some one could help. I have ospf running on 2 routers R1
>> and
>> > R2.
>> > R2 is a PPPoE client and R1 is the server. R2 has a negotiated ip
>> address
>> > on the dialer interface from R1 which is host (/32) address while R1
>> has a
>> > /29 bit Ip address on its interface facing towards Client.
>> > OSPF adj is not coming up between the client and Server
>> > On client dialer int and Server int I have ip ospf network
>> > point-to-multipoint
>> > i also tried no peer neighbor-route on client dialer interface.
>> >
>> > debugs on the client side show:
>> > OSPF: Rcv pkt from 172.31.29.1, Dialer16, area 0.0.0.3 : src not on the
>> > same network
>> >
>> > I have tried changing the network type to poin-to-poitn as well but no
>> adj
>> >
>> > Regards
>> >
>> >
>> > Blogs and organic groups at http://www.ccie.net
>> >
>> > _______________________________________________________________________
>> > Subscription information may be found at:
>> > http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Wed Nov 28 2012 - 11:24:58 ART