Re: gns3

John,
This image will have everything you need (IPv6, MPLS, EEM, OER/PfR, etc):

R5# sho ver
Cisco IOS Software, 3700 Software (C3725-ADVENTERPRISEK9_IVS-M), Version
12.4(15)T13, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 07-Apr-10 12:44 by prod_rel_team

ROM: ROMMON Emulation Microcode
ROM: 3700 Software (C3725-ADVENTERPRISEK9_IVS-M), Version 12.4(15)T13,
RELEASE SOFTWARE (fc3)

R5 uptime is 9 minutes
System returned to ROM by unknown reload cause - suspect
boot_data[BOOT_COUNT] 0x0, BOOT_COUNT 0, BOOTDATA 19
System image file is "tftp://255.255.255.255/unknown"

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be
found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export_at_cisco.com.

Cisco 3725 (R7000) processor (revision 0.1) with 249856K/12288K bytes of
memory.
Processor board ID FTX0945W0MY
R7000 CPU at 240MHz, Implementation 39, Rev 2.1, 256KB L2, 512KB L3 Cache
2 FastEthernet interfaces
DRAM configuration is 64 bits wide with parity enabled.
55K bytes of NVRAM.
16384K bytes of ATA System CompactFlash (Read/Write)

Configuration register is 0x2102

R5#

-- 
Brian Dennis, CCIEx5 #2210 (R&S/ISP-Dial/Security/SP/Voice)
bdennis_at_ine.com
Internetwork Expert, Inc.
http://www.INE.com
On 03/21/2012 05:47 AM, john matijevic wrote:
> Good Morning Brian,
>
> Are you able to run IPV6 over EIGRP with this image?
> For example the following command under an interface:
> ipv6 eigrp 1
> or to enable IPV6 with EIGRP in Global config:
> ipv6 router eigrp 1
>
>
> I have a similar image but cannot.
>
> Also are you able to configure the following commands with MPLS?
> address-family vpnv4
> mpls ip
>
> again I cannot run these commands with image I have.
>
>
>
>
>
> Regards,
> John
>
> On 3/16/12, Brian Dennis<bdennis_at_ine.com>  wrote:
>> R3#sho ver
>> Cisco IOS Software, 3700 Software (C3725-ADVENTERPRISEK9_IVS-M), Version
>> 12.4(15)T13, RELEASE SOFTWARE (fc3)
>> Technical Support: http://www.cisco.com/techsupport
>> Copyright (c) 1986-2010 by Cisco Systems, Inc.
>> Compiled Wed 07-Apr-10 12:44 by prod_rel_team
>>
>> R6#sho ver
>> Cisco IOS Software, 7200 Software (C7200P-ADVENTERPRISEK9-M), Version
>> 12.4(24)T3, RELEASE SOFTWARE (fc2)
>> Technical Support: http://www.cisco.com/techsupport
>> Copyright (c) 1986-2010 by Cisco Systems, Inc.
>> Compiled Tue 23-Mar-10 13:16 by prod_rel_team
>>
>> brian_at_CCIE2210 ~ $  ./dynamips-0.2.8-RC3-community-x86_64.bin
>> Cisco Router Simulation Platform (version 0.2.8-RC3-amd64/Linux stable)
>> Copyright (c) 2005-2011 Christophe Fillot.
>> Build date: Nov 12 2011 18:42:02
>>
>> brian_at_CCIE2210 ~ $ lshw -class processor
>>     *-cpu
>>          description: CPU
>>          product: Intel(R) Core(TM) i7-2960XM CPU @ 2.70GHz
>>          vendor: Intel Corp.
>>          physical id: 1
>>          bus info: cpu_at_0
>>          version: Intel(R) Core(TM) i7-2960XM CPU @ 2.70GHz
>>          serial: Not Supported by CPU
>>          slot: CPU
>>          size: 1800MHz
>>          capacity: 1800MHz
>>          width: 64 bits
>>          clock: 100MHz
>>          capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae
>> mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr
>> sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs
>> bts nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor
>> ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 x2apic popcnt
>> aes xsave avx lahf_lm ida arat epb xsaveopt pln pts tpr_shadow vnmi
>> flexpriority ept vpid cpufreq
>>          configuration: cores=4 enabledcores=4 threads=8
>>
>> brian_at_CCIE2210 ~ $  uname -a
>> Linux CCIE2210 3.0.0-12-generic #20-Ubuntu SMP Fri Oct 7 14:56:25 UTC
>> 2011 x86_64 x86_64 x86_64 GNU/Linux
>>
>> --
>> Brian Dennis, CCIEx5 #2210 (R&S/ISP-Dial/Security/SP/Voice)
>> bdennis_at_ine.com
>>
>> Internetwork Expert, Inc.
>> http://www.INE.com
>>
>>
>> On 03/15/2012 09:59 PM, Nish Vamadevan wrote:
>>> hi Brian,
>>>
>>> Which ios version do you use, the exact code?
>>>
>>> Cheers!
>>>
>>> Sent from my BlackBerry. wireless device
>>>
>>> -----Original Message-----
>>> From: Brian Dennis<bdennis_at_ine.com>
>>> Sender: nobody_at_groupstudy.com
>>> Date: Thu, 15 Mar 2012 21:41:04
>>> To:<ccielab_at_groupstudy.com>
>>> Reply-To: Brian Dennis<bdennis_at_ine.com>
>>> Subject: Re: gns3
>>>
>>> I use GNS3 on Mint 12 (Lenovo W520) with an Intel Core i7-2920X and 16GB
>>> of RAM.  This can easily run 10 routers and not break above 15 or 20%
>>> CPU once the idle-pc is configured.  No matter what hardware you use,
>>> the idle-pc value is key.
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net