RE: "match ip route-source" Command Issue...

Thanks Tom, much appriciated!!!

Rob

> Date: Wed, 8 Feb 2012 15:20:19 -0600
> Subject: Re: "match ip route-source" Command Issue...
> From: tom.kac_at_gmail.com
> To: guile474_at_hotmail.com
> CC: ccielab_at_groupstudy.com
>
> Check this link out
>
http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a008047915d.
shtml#tables
>
> Basically this will tell you which route-map options are supported when
> redistributing, in this case using a route-source with prefix list is not
> supported but with ACL it is supported for all routing protocols.
>
> Hope that helps
>
> Tom Kacprzynski
>
>
>
>
> On Wed, Feb 8, 2012 at 2:10 PM, Robert Miele <guile474_at_hotmail.com> wrote:
>
> > Hello all,
> >
> > I am working on INE lab 3 in volume 2 and am having an issue with section
> > 2.2.
> > Long story short, I am attempting to have R6 (who is redistributing
between
> > RIP & EIGRP) tag routes from BB1 (Source: 54.1.3.254; In RIP) as 1 and
BB3
> > (Source: 204.12.1.254; In RIP) as 2 using the "match ip route-source"
> > command.
> > See below:
> >
> > ip prefix-list From_BB1 seq 5 permit 54.1.3.254/32
> > ip prefix-list From_BB3 seq 5 permit 204.12.1.254/32
> >
> > route-map RIP-to-EIGRP permit 10
> > match ip route-source prefix-list From_BB1
> > set tag 1
> >
> > route-map RIP-to-EIGRP permit 20
> > match ip route-source prefix-list From_BB3
> > set tag 2
> >
> > route-map RIP-to-EIGRP permit 30
> >
> > router eigrp 100
> > redistribute rip metric 10000 1000 100 1 1500 route-map RIP-to-EIGRP
> >
> >
> >
> > This does not work, the routes just pass through un-tagged via the last
> > route-map statement. When I switch to standard ACL's to identify the
> > route-sources, it works. See below:
> >
> > access-list 1 permit 54.1.3.254
> >
> >
> >
> > access-list 2 permit 204.12.1.254
> >
> > route-map RIP-to-EIGRP permit 10
> >
> > match ip route-source 1
> >
> > set tag 1
> >
> >
> >
> > route-map RIP-to-EIGRP permit 20
> >
> > match ip route-source 2
> >
> > set tag 2
> >
> >
> >
> > route-map RIP-to-EIGRP permit 30
> >
> >
> >
> > router eigrp 100
> >
> > redistribute rip metric 10000 1000 100 1 1500 route-map RIP-to-EIGRP
> >
> >
> > What am I missing here? Am I using the prefix-list incorrectly?
> >
> > Thanks,
> > Rob
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Thu Feb 09 2012 - 02:05:09 ART