Re: EIGRP over tunnel interface

I meant 10.5.5.2 from R1

----- Original Message -----
From: amin [mailto:amin_at_axizo.com]
Sent: Monday, October 17, 2011 09:27 AM
To: Joseph L. Brunner; ccielab_at_groupstudy.com <ccielab_at_groupstudy.com>
Subject: RE: EIGRP over tunnel interface

Al_Qubba#ping 10.5.5.1 repeat 1000

Type escape sequence to abort.
Sending 1000, 100-byte ICMP Echos to 10.5.5.1, timeout is 2 seconds:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!
Success rate is 100 percent (1000/1000), round-trip min/avg/max = 12/12/280
ms

-----Original Message-----
From: Joseph L. Brunner [mailto:joe_at_affirmedsystems.com]
Sent: Monday, October 17, 2011 2:58 PM
To: amin; ccielab_at_groupstudy.com
Subject: RE: EIGRP over tunnel interface

>the tunnel is 100% working

No its not. If it was eigrp would stay up.

Do this - run a continuous ping from R1 to R2, i.e.

Ping 10.5.5.1 re 100000

Does 1 ping fail?

-----Original Message-----
From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of amin
Sent: Monday, October 17, 2011 8:49 AM
To: ccielab_at_groupstudy.com
Subject: EIGRP over tunnel interface

Hi experts,

Strange case in configuring EIGRP over gre tunnel, no neighbors on R1, R2
see R1 as a neighbor but always give me retry time exceeded, the tunnel is
100% working:-

R1

interface Tunnel40

ip address 10.5.5.1 255.255.255.0

tunnel source 10.10.10.102

 tunnel destination 192.168.71.2

ip route 192.168.71.0 255.255.255.128 10.10.10.101 h static route to reach
the destination

interface Serial0/1/0:1

ip address 10.10.10.102 255.255.255.252 h Tunnel source

router eigrp 100

network 10.5.5.0 0.0.0.255

no auto-summary

R2

interface Tunnel0

ip address 10.5.5.2 255.255.255.0

tunnel source 192.168.71.2

 tunnel destination 10.10.10.102

ip route 10.10.10.100 255.255.255.252 192.168.71.1 h static route for the
destination

interface FastEthernet0/1

ip address 192.168.71.129 255.255.255.128 h Tunnel source

router eigrp 100

 network 10.5.5.0 0.0.0.255

 no auto-summary

show ip eigrp neighbor

H Address Interface Hold Uptime SRTT RTO Q Seq

                                                                 (sec)
(ms) Cnt Num

0 10.5.5.1 Tu0 79 00:00:39 1
5000 2 0

Debug ip eigrp

*Oct 17 12:53:41.679: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 10.5.5.1
(Tunnel0) is down: retry limit exceeded

*Oct 17 12:53:53.971: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 10.5.5.1
(Tunnel0) is up: new adjacency

Regards,

Amin

Blogs and organic groups at http://www.ccie.net
Received on Mon Oct 17 2011 - 13:29:33 ART