RE: Internet Traffic load balancing

Here you go:

http://www.cisco.com/en/US/tech/tk648/tk361/technologies_configuration_examp
le09186a0080950834.shtml

In conjunction with ZBFW:

http://www.cisco.com/en/US/products/sw/secursw/ps1018/products_configuration
_example09186a00809454c7.shtml

You can use two Ethernet (fast or gig) interfaces for the configuration. The
example they give is Ethernet and dialer.

This allows:
2 ISPs
Use of only static route out
Failover
Both connections into one router

Travis

-----Original Message-----
From: Jay McMickle [mailto:jay.mcmickle_at_yahoo.com]
Sent: Monday, May 02, 2011 12:34 PM
To: Travis Niedens
Cc: masroor ali; Shaun Gomez (4g1vn); Cisco certification
Subject: Re: Internet Traffic load balancing

Travis- interesting suggestion. I was unaware of that feature. Can you post
a Cisco link? I'm prepping for my CCIE R&S, but it appears that if it's not
on the blueprint, I've avoided any new technologies. That's where this come
in.
Thanks again.

Regards,
Jay McMickle- CCNP,CCSP,CCDP
Sent from my iPhone
http://mycciepursuit.wordpress.com

On May 2, 2011, at 1:33 PM, Travis Niedens <niedentj_at_hotmail.com> wrote:

> If they will connect into the same router you can use IOS Nat
loadbalancing.
> I have configured it and it works pretty well however I did not see
> how you could specify the load balance percentage.
>
> Travis
>
> -----Original Message-----
> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf
> Of masroor ali
> Sent: Monday, May 02, 2011 11:27 AM
> To: Shaun Gomez (4g1vn)
> Cc: Cisco certification
> Subject: Re: Internet Traffic load balancing
>
> these are just two internet links. no BGP only default routes will be
used.
>
> On Mon, May 2, 2011 at 5:38 PM, Shaun Gomez (4g1vn)
> <shaun.gomez_at_gmail.com>wrote:
>
>> Are you multihomed via BGP to the SP/SPs? Are we talking about
>> traffic flows away from the enterprise (enterprise egress) or into
>> the enterprise (enterprise ingress)?
>>
>> On Mon, May 2, 2011 at 9:15 AM, masroor ali <masror.ali_at_gmail.com> wrote:
>>
>>> Hi,
>>>
>>> I have two internet links, one link is of 5 Mb and other link is of
>>> 1Mb, I need to configure router so that, The link of 5 MB should
>>> take 70% load, other should take 30%. If one link goes down all
>>> traffic should use other link.
>>>
>>>
>>>
>>> Thanks & Regards,
>>> Masroor Ali
>>>
>>>
>>> Blogs and organic groups at http://www.ccie.net
>>>
>>> ____________________________________________________________________
>>> _ __ Subscription information may be found at:
>>> http://www.groupstudy.com/list/CCIELab.html
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>
>
>
> --
> Thanks & Regards,
> Masroor Ali
> http://www.linkedin.com/pub/masroor-ali-ccie-27170/10/626/53
>
>
> Blogs and organic groups at http://www.ccie.net
>
> ______________________________________________________________________
> _ Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> ______________________________________________________________________
> _ Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Mon May 02 2011 - 13:48:05 ART