Re: ASR9K question please...not sure if this is OT or not...but

IOS XR 4.0.1 supports BVI for its bridge groups. I'm still really new
to ASRs, but they really don't seem to want to do L2 much at all in
any way similar to Catalyst switches or 7600 routes. It's not as
simple as creating a VLAN and L3 VLAN interface. You can create a
bridge group and then assign a BVI to it, but it has some limitations.
One that I know of is that ACLs are not supported on BVIs.

The ASR9K doesn't seem like a good choice to me if you need a lot of
L2 stuff. We've been wrestling with similar issues in our test lab on
our new ASR9Ks.

HTH,
John

On Wed, Mar 23, 2011 at 2:27 PM, Rob Laidlaw <laidlaw_at_consecro.com> wrote:
> I have had to do something similair on the ASR1K series. You have to use
> the Carrier Ethernet services to create a virtual layer 2 switch. The 9K
> supports it but you may have to upgrade code if yours doesn't have it. Here
> is the config guide:
>
> http://www.cisco.com/en/US/docs/routers/asr9000/software/asr9k_r3.9/lxvpn/configuration/guide/lesc39ethi.html
>
> Its similar to deploying VPLS in a Service Provider environment, but it
> works locally too.
>
> GL
>
> -Rob
>
> On Wed, Mar 23, 2011 at 3:01 PM, Aaron <aaron1_at_gvtc.com> wrote:
>
>> I have a SP Video architecture (CATV/VoD/PPV type thing) in place, testing,
>> and operational to some extent using 4506 and 4503 on both ends..
>>
>>
>>
>> Digital Content Managers (DCM's) are putting out mcast video.
>> 239dot..mcast
>> groups.
>>
>>
>>
>> Mcast listeners/IGMP joiners, are Video and Audio Edge Modulators and
>> GQAMs.. (y'all may have heard of some of this SciAtl (Scientific Atlanta)
>> product line, I believe acquired by cisco about 2 years ago)
>>
>>
>>
>> .hang in there, I'll get to my networking question.
>>
>>
>>
>> 4500's are doing EIGRP and PIM-SM to allow for support of the above end
>> equipment..also, the edge mods and GQAMs are group in vlan's with SVI's
>> inside the 4500's where I route this subnets, handle igmp joins, etc
>>
>>
>>
>> We are upgrading our 4500's to ASR9K's..9006 on one end and 9010 on the
>> other end..
>>
>>
>>
>> Guess what I found out today..$100K later..the ASR is naturally a router.
>> Not able to simply drop it in place of the 4500's as I've stated above, the
>> 4500's are doing L2 and L3 combined. ASR doesn't naturally do that, as I
>> now understand it to be like a 2500 (old), or 3660, 7206vxr, 3825, 7513,
>> etc,etc..you get my point, pure router. Not like 3550,3560,6500,7600.
>>
>>
>>
>> What do y'all think about my making the ASR9K's fit into the current
>> architecture of my existing 4500's by using IRB/bridge groups, and routing
>> the irb interfaces much like I have the vlans and svi's in my current
>> 4500's? any cautions? This seem ok to y'all?
>>
>>
>>
>> I'll take any advice I can get
>>
>>
>>
>> Aaron
>>
>>
>>
>> p.s. I heard today that IOS XR 4.1 supports IRB
>>
>>
>>
>> p.s.s. I'm new to ASRs, I'm new to IOS XR, I'm not that experienced with
>> IRB. IRB/CRB was something I messed with about 10 years ago for something
>> I
>> hardly recall.
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Wed Mar 23 2011 - 14:33:53 ART