No, it's not needed in new versions. It's possible it was needed when the feature was first released. The IPv6 protocols should normally pull their RIDs from an IPv4 interface just like their v4 counterparts. Like you said though, if you're not running dual-stack then you need to configure it manually.
Brian McGahan, CCIE #8593 (R&S/SP/Security)
bmcgahan_at_INE.com<mailto:bmcgahan_at_INE.com>
Internetwork Expert, Inc.
http://www.INE.com
On Feb 1, 2011, at 1:44 PM, "Scott M Vermillion" <scott_ccie_list_at_it-ag.com<mailto:scott_ccie_list_at_it-ag.com>> wrote:
Well, I certainly haven't encountered EIGRPv6 in the real world and the code I'm running in my current lab setup doesn't support it, so perhaps I am mistaken. My old notes from R&S lab prep state that the 'router-id' command is required under the EIGRPv6 process, regardless of whether or not any interfaces have been assigned IPv4 addresses. It wouldn't be the first time one of my notes was either just flat out incorrect or had become OBE over the past few years...
____________________________________________
There are only 10 types of people in the world:
Those who understand binary and those who do not...
On Feb 1, 2011, at 12:25 , Brian McGahan wrote:
In IPv6 as well. All designs can be solved without the need for the use of the router-I'd command, both in IPv4 and IPv6. The only issue is that within the scope of the lab, they may say don't do X or dint use command Y, in which case you may be limited as to your viable solutions.
Brian McGahan, CCIE #8593 (R&S/SP/Security)
bmcgahan_at_INE.com<mailto:bmcgahan_at_INE.com><<mailto:bmcgahan_at_INE.com>mailto:bmcgahan_at_INE.com>
Internetwork Expert, Inc.
<http://www.INE.com>http://www.INE.com
On Feb 1, 2011, at 12:58 PM, "Scott M Vermillion" <scott_ccie_list_at_it-ag.com<mailto:scott_ccie_list_at_it-ag.com><mailto:scott_ccie_list_at_it-ag.com>> wrote:
Likewise there is never a case where you *have* to define the router-I'd manually.
In the case of IPv4, anyway, no?
____________________________________________
There are only 10 types of people in the world:
Those who understand binary and those who do not...
On Feb 1, 2011, at 10:47 , Brian McGahan wrote:
Likewise there is never a case where you *have* to define the router-I'd manually. Whether a routing process is in the global table or a vrf table, the highest loopback that is up/up when the process starts will be the RID. If no loopback exists then the highest address on any other link will be used.
Setting the RID is good design practice, and can make troubleshooting easier. If different routers have the same RID, like in an anycast design, different protocols can have different problems.
So now the question should be, what are these problems? If you know this then it will tell you when it's a good idea to set the RID manually.
Brian McGahan, CCIE #8593 (R&S/SP/Security)
<mailto:bmcgahan_at_INE.com>bmcgahan_at_INE.com<mailto:bmcgahan_at_INE.com>
Internetwork Expert, Inc.
http://www.INE.com
On Feb 1, 2011, at 10:40 AM, "Hussam EL Kebbi" <hussamkibbi_at_hotmail.com> wrote:
ccielab_at_groupstudy.com
Blogs and organic groups at http://www.ccie.net
Received on Tue Feb 01 2011 - 13:48:49 ART
This archive was generated by hypermail 2.2.0 : Tue Mar 01 2011 - 07:01:49 ART