Re: OT: EEM with Applet Policy

Sorry,
I fail to see where it says that "pattern" has to match the "entire
line". Would you please show me ?

-Carlos

Jay McMickle @ 09/01/2011 10:19 -0300 dixit:
> I'm new to EEM as well, but I did find a useful link that validates Stephen's
> point.
> http://www.cisco.com/en/US/prod/collateral/iosswrel/ps6537/ps6555/ps6815/conf
> ig_guide_eem_configuration_for_cisco_integrated_services_router_platforms.html
>
>
> Regards,
> Jay McMickle- CCNP, CCSP, CCDP, MCSE
> http://mycciepursuit.wordpress.com/
>
>
>
>
>
> ________________________________
> From: Stephen Okoye <tosco12_at_yahoo.co.uk>
> To: Bilal Hansrod
> <bilal.hansrod_at_gmail.com>; Cisco certification
> <ccielab_at_groupstudy.com>
> Sent:
> Sat, January 8, 2011 10:14:29 AM
> Subject: Re: OT: EEM with Applet Policy
>
> Hi,
> Your script is ok but it looks as if you are not capturing the entire message.
> I
> think you will have to start from "%LINEPROTO-5-UPDOWN...." all the way to
> the
> end
>
>
>
> Sent from my BlackBerry wireless device from MTN
>
> -----Original
> Message-----
> From: Bilal Hansrod <bilal.hansrod_at_gmail.com>
> Sender:
> nobody_at_groupstudy.com
> Date: Sun, 9 Jan 2011 02:52:17
> To: Cisco
> certification<ccielab_at_groupstudy.com>
> Reply-To: Bilal Hansrod
> <bilal.hansrod_at_gmail.com>
> Subject: OT: EEM with Applet Policy
>
> I am very new
> to EEM scripting and just read few examples on internet and
> came with below
> scripts. It seems the script works sometimes. I want to trap
> line protocol
> message for specific interface and shutdown another interface
> permanently. The
> script as below, Can someone please advise me if I have
> missed something. Out
> of 5-6 tests, I was successful twice! I am using this
> script on GNS3 (heads
> up).
>
> event manager applet TEST
> event syslog pattern "Line protocol on
> Interface FastEthernet0/0, changed
> state to down"
> action 1.0 cli command
> "enable"
> action 1.1 cli command "configure term"
> action 1.2 cli command
> "interface FastEthernet0/1"
> action 1.3 cli command "shutdown"
>
> Any
> suggestions.
>
> Regards,
>
> Bilal Hansrod
>
>
> Blogs and organic groups at
> http://www.ccie.net
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at
> http://www.ccie.net
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>

-- 
Carlos G Mendioroz  <tron_at_huapi.ba.ar>  LW7 EQI  Argentina
Blogs and organic groups at http://www.ccie.net