Re: Ip Tracking question

your track says to install that route if you have that route, so when you
add that route it comes up and when you do not have the route it does not
install it...

see this example, i have a BGP route to 4.4.4.4/32 in my routing table and
when i add a track to track that the route is up and then i add a tracked
static route to null 0 it installs the route, because it is up via BGP:

R1#sh ip route 4.4.4.4
Routing entry for 4.4.4.4/32
  Known via "bgp 1", distance 20, metric 0
  Tag 2, type external
  Last update from 12.12.12.2 00:00:09 ago
  Routing Descriptor Blocks:
  * 12.12.12.2, from 12.12.12.2, 00:00:09 ago
      Route metric is 0, traffic share count is 1
      AS Hops 2
      Route tag 2

R1#sh track 1
Track 1
  IP route 4.4.4.4 255.255.255.255 reachability
  Reachability is Up (BGP)
    1 change, last change 00:02:59
  First-hop interface is FastEthernet0/0

R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#ip route 4.4.4.4 255.255.255.255 Null0 track 1

R1(config)#do sh track 1
Track 1
  IP route 4.4.4.4 255.255.255.255 reachability
  Reachability is Up (static)
    1 change, last change 00:03:18
  First-hop interface is Null0
  Tracked by:
    STATIC-IP-ROUTING 0

R1(config)#do sh ip route 4.4.4.4
Routing entry for 4.4.4.4/32
  Known via "static", distance 1, metric 0 (connected)
  Routing Descriptor Blocks:
  * directly connected, via Null0
      Route metric is 0, traffic share count is 1

--
Garry L. Baker
"There is no 'patch' for stupidity." - www.sqlsecurity.com
On Wed, Dec 1, 2010 at 12:25 PM, Naufal Jamal <naufalccie_at_yahoo.in> wrote:
> I am trying to configure ip route tracking on a router.
>
> R1 and R2 are connected point to point. I am configuring  a track on R1 for
> reachablity for R2's loopback0  ip. I have given a static route in R1 for
> reaching loopback0 of R2. I want this static route to be disappeared from
> my
> R1 routing table when this loopback is unreachable. This is not happeneing.
>
> R1
>
> track 1 ip route 2.2.2.2 255.255.255.255 reachability
> delay down 2 up 2
>
> interface FastEthernet0/0
> ip address 1.1.1.1 255.255.255.252
> duplex auto
> speed auto
>
> ip route 2.2.2.2 255.255.255.255 1.1.1.2 track 1
>
> ip route 2.2.2.2 255.255.255.255 1.1.1.2 (The track comes up only after
> entering this statement,Is it neccessary to add this route as well.)
>
> R2
>
> interface FastEthernet0/0
> ip address 1.1.1.2 255.255.255.252
> duplex auto
> speed auto
>
> interface loopback0
> ip address 2.2.2.2 255.255.255.255
>
> when I shut down loopback0 on R2 the track doesnt go down in R1
>
> R1(config)#do ping 2.2.2.2
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
> U.U.U
> Success rate is 0 percent (0/5)
>
> R1(config)#do sh track
> Track 1
>  IP route 2.2.2.2 255.255.255.255 reachability
>  Reachability is Up (static)
>    8 changes, last change 00:02:27
>  Delay up 2 secs, down 2 secs
>  First-hop interface is FastEthernet0/0
>  Tracked by:
>    STATIC-IP-ROUTING 0
>
> Why it is showing up when 2.2.2.2 is no more reachable
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net