RE: Dual Active LACP Nexus -OT

Also, you may want to see the "sh run all" and "sh run int e100/1/2 all"
and compare the configs on both of the N5Ks.

-----Original Message-----
From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of Ram
Hispren Shummoogum
Sent: Wednesday, November 03, 2010 8:08 PM
To: ccielab_at_groupstudy.com
Subject: Dual Active LACP Nexus -OT

I am two ports of a 6509 in an L3 LACP config to simulate a server with two
NICS.
one port going to an N2K and the other gointg to a second N2K. Each N2K is
connected to its respective N5K in a VPC mode.
This is a supported topolgy.

Not sure why the port-channel is down------------->>
on the 6509 the portchannel is ip and I can ping the IP.
any help appreciated.

w-cr-nx5020-1# sh int port 11
*port-channel11 is down (inactive)
*vPC Status: Up, vPC number: 11
  Hardware: Port-Channel, address: 5475.d021.1e83 (bia 5475.d021.1e83)
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,

@@@@@@@@@@@@@@@@@@@@@@@

gw-cr-nx5020-1# sh run int port 11

!Command: show running-config interface port-channel11
!Time: Wed Nov 3 13:36:25 2010

version 4.2(1)N2(1)

interface port-channel11
  vpc 11
  switchport access vlan 377

@@@@@@@@@@@@@@@@@@@@@@@@@@@@

gw-cr-nx5020-1# sh run int e100/1/2

!Command: show running-config interface Ethernet100/1/2
!Time: Wed Nov 3 13:36:33 2010

version 4.2(1)N2(1)

interface Ethernet100/1/2
  switchport access vlan 377
  channel-group 11 mode active

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

gw-cr-nx5020-1# sh port-channel summary
Flags: D - Down P - Up in port-channel (members)
        I - Individual H - Hot-standby (LACP only)
        s - Suspended r - Module-removed
        S - Switched R - Routed
        U - Up (port-channel)
----------------------------------------------------------------------------

----
Group Port-       Type     Protocol  Member Ports
      Channel
----------------------------------------------------------------------------
----
1     Po1(SU)     Eth      LACP      Eth1/38(P)   Eth1/40(P)
10    Po10(SD)    Eth      NONE      Eth100/1/1(D)
11    Po11(SD)    Eth      LACP      Eth100/1/2(P)
100   Po100(SU)   Eth      NONE      Eth1/17(P)   Eth1/19(D)
102   Po102(SD)   Eth      NONE      Eth1/33(D)   Eth1/35(D)
gw-cr-nx5020-1#
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
w-cr-nx5020-1# sh vpc
Legend:
                (*) - local vPC is down, forwarding via vPC peer-link
vPC domain id                   : 1
Peer status                     : peer adjacency formed ok
vPC keep-alive status           : peer is alive
Configuration consistency status: failed
Configuration consistency reason: vPC type-1 configuration incompatible -
STP gl
obal port type inconsistent
vPC role                        : primary
Number of vPCs configured       : 2
Peer Gateway                    : Disabled
Dual-active excluded VLANs      : -
vPC Peer-link status
---------------------------------------------------------------------
id   Port   Status Active vlans
--   ----   ------ --------------------------------------------------
1    Po1    up     -
vPC status
----------------------------------------------------------------------------
id     Port        Status Consistency Reason                     Active
vlans
------ ----------- ------ ----------- -------------------------- -----------
10     Po10        down*  failed      Global compat check failed -
11     Po11        down   failed      Global compat check failed -
I have no clue about what Global compatibility is failed.
Thanks for helping:
Blogs and organic groups at http://www.ccie.net