RE: OT: HWIC-3G-GSM Module Configration Problem...need help

Hi

You will need to set up a ppp profile for the process to work. The (chap or
pap) username and password are just dummies but they must be defined.

This link should help:

http://inetpro.org/wiki/Initial_configuration_of_a_881G_router_Cellular_inte
rface#Create_a_Profile_specific_to_your_mobile_ISP

-
Daniel

-----Original Message-----
From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
muhammad adnan
Sent: Samstag, 30. Oktober 2010 16:25
To: Bilal Hansrod
Cc: Cisco certification
Subject: Re: OT: HWIC-3G-GSM Module Configration Problem...need help

Dear bilal:- one corection --> did not

 i *didnot* configure the parameter ppp authentication pap or chap because
if i configure ppp authentication then i must provide username and password
but service provide ask that the usename and password is blank and i am
accessing the internet over my cell phone without any username or password

Thanks a lot
Adnan

On Sat, Oct 30, 2010 at 4:09 PM, muhammad adnan
<taurusadnan19_at_gmail.com>wrote:

> Dear bilal:-
> i did configure the parameter ppp authentication pap or chap because
> if i configure ppp authentication then i must provide username and
> password but service provide ask that the usename and password is
> blank and i am accessing the internet over my cell phone without any
> username or password
>
> Thanks a lot
> Adnan
>
>
> On Sat, Oct 30, 2010 at 4:01 PM, Bilal Hansrod
<bilal.hansrod_at_gmail.com>wrote:
>
>> What output do you see when you run below debugs suggested by ERDEM
>>
>> debug chat
>> debug ppp negotiation
>> debug ppp error
>> debug ppp event
>>
>> Regards,
>>
>> Bilal
>>
>>
>> On Sun, Oct 31, 2010 at 12:45 AM, muhammad adnan
>> <taurusadnan19_at_gmail.com
>> > wrote:
>>
>>> Dear
>>> i am using internet when i placed my sim in my cell phone.if the
>>> Data is not activated then how i can access.
>>>
>>> Thanks
>>>
>>>
>>>
>>>
>>>
>>> On Sat, Oct 30, 2010 at 3:36 PM, Radioactive Frog
<pbhatkoti_at_gmail.com>wrote:
>>>
>>>> I am not sure if you've already done this but take the SIM card out
>>>> from the cellular module and put it in your SmartPhone - Sort out
>>>> the activation isssue first. Make sure data is activated on that SIM.
>>>>
>>>> Then play it once above is confirmed.
>>>>
>>>>
>>>>
>>>> On Sat, Oct 30, 2010 at 11:56 PM, muhammad adnan <
>>>> taurusadnan19_at_gmail.com> wrote:
>>>>
>>>>> Dear Bilal
>>>>> Router#show cellular 0/1/0 all
>>>>> Hardware Information
>>>>> ====================
>>>>> Modem Firmware Version = H1_1_9_3MCAP C:/WS/ Modem Firmware built
>>>>> = 12/12/07 Hardware Version = 1.0 International Mobile Subscriber
>>>>> Identity (IMSI) = 606010105114370 International Mobile Equipment
>>>>> Identity (IMEI) = 011359000487907 Factory Serial Number (FSN) =
>>>>> D28026013381043 Modem Status = Online Current Modem Temperature =
>>>>> 26 deg C, State = Normal
>>>>>
>>>>> Profile Information
>>>>> ====================
>>>>> Profile 1 = INACTIVE*
>>>>> --------
>>>>> PDP Type = IPv4
>>>>> Access Point Name (APN) = almadar.net Authentication = None
>>>>> Username: , Password:
>>>>>
>>>>> * - Default profile
>>>>>
>>>>> Data Connection Information
>>>>> ===========================
>>>>> Data Transmitted = 0 bytes, Received = 0 bytes Profile 1, Packet
>>>>> Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 2,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 3,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 4,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 5,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 6,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 7,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 8,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 9,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 10,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 11,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 12,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 13,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 14,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 15,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state Profile 16,
>>>>> Packet Session Status = INACTIVE
>>>>> Inactivity Reason = Normal inactivate state
>>>>>
>>>>> Network Information
>>>>> ===================
>>>>> Current Service Status = Normal, Service Error = None Current
>>>>> Service = Combined Packet Service = GPRS (Attached) Packet Session
>>>>> Status = Inactive Current Roaming Status = Home Network Selection
>>>>> Mode = Automatic Country = 606, Network = 606 01 Mobile Country
>>>>> Code (MCC) = 606 Mobile Network Code (MNC) = 1 Location Area Code
>>>>> (LAC) = 1 Routing Area Code (RAC) = 1 Cell ID = 11071 Primary
>>>>> Scrambling Code = 0 PLMN Selection = Automatic Registered PLMN =
>>>>> Libya Al Madar , Abbreviated = 606 01 Service Provider = 606 01
>>>>>
>>>>> Radio Information
>>>>> =================
>>>>> Current Band = GSM 900, Channel Number = 5 Current RSSI = -62 dBm
>>>>> Band Selected = Auto
>>>>>
>>>>> Modem Security Information
>>>>> ==========================
>>>>> Card Holder Verification (CHV1) = Disabled SIM Status = OK SIM
>>>>> User Operation Required = None Number of Retries remaining = 3
>>>>>
>>>>>
>>>>> Thanks
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> On Sat, Oct 30, 2010 at 2:42 PM, Bilal Hansrod <
>>>>> bilal.hansrod_at_gmail.com>wrote:
>>>>>
>>>>> > Can you please send the output of *sh cell 0/1/0 all*
>>>>> >
>>>>> >
>>>>> > Bilal
>>>>> >
>>>>> >
>>>>> > On Sat, Oct 30, 2010 at 11:36 PM, muhammad adnan <
>>>>> taurusadnan19_at_gmail.com>wrote:
>>>>> >
>>>>> >> Dear Bilal i configure according to the Cisco Documentation and
>>>>> >> in my mail i pasted show run config...
>>>>> >>
>>>>> >>
>>>>> >>
>>>>> >>
>>>>> http://www.cisco.com/en/US/docs/routers/access/1800/1861/software/
>>>>> feature/guide/mrwlsgsm.html#wp1040391
>>>>> >>
>>>>> >> in my mail i ask that username and password is blank to access
>>>>> >> the internet Service provider ask me no authentication username
>>>>> >> and password
>>>>> blank ("i
>>>>> >> just put Apn in my phone and username and password blank and it
>>>>> works fine
>>>>> >> accessing the internet")
>>>>> >>
>>>>> >> if u need any more information kindly let me know again..
>>>>> >>
>>>>> >> Thanks
>>>>> >> Muhammad Adnan
>>>>> >>
>>>>> >>
>>>>> >>
>>>>> >> On Sat, Oct 30, 2010 at 2:28 PM, Bilal Hansrod <
>>>>> bilal.hansrod_at_gmail.com>wrote:
>>>>> >>
>>>>> >>> Hi Muhammad,
>>>>> >>>
>>>>> >>> I can't see a logical interface created for cell interface
>>>>> >>> where
>>>>> you
>>>>> >>> define your PPP username/password and also the authentication
>>>>> method.
>>>>> >>>
>>>>> >>> An example from my config as below:
>>>>> >>>
>>>>> >>>
>>>>> >>> interface Dialer1
>>>>> >>> ip address negotiated
>>>>> >>> ip virtual-reassembly
>>>>> >>> encapsulation ppp
>>>>> >>> dialer pool 1
>>>>> >>> dialer idle-timeout 0
>>>>> >>> dialer string gsm
>>>>> >>> dialer persistent
>>>>> >>> dialer-group 1
>>>>> >>> no cdp enable
>>>>> >>> ppp authentication chap callin ppp chap hostname XXX ppp
>>>>> >>> chap password YYY
>>>>> >>>
>>>>> >>>
>>>>> >>> Regards,
>>>>> >>>
>>>>> >>> Bilal
>>>>> >>>
>>>>> >>>
>>>>> >>> On Sat, Oct 30, 2010 at 11:05 PM, muhammad adnan <
>>>>> >>> taurusadnan19_at_gmail.com> wrote:
>>>>> >>>
>>>>> >>>> Dear Group members:-
>>>>> >>>> i am trying to configure the
>>>>> 3G-module.i
>>>>> >>>> have inserted my sim card into the HWIC module sim card
>>>>> >>>> properly working in the phone and i am accessing the
>>>>> >>>> internet.
>>>>> >>>> but when i configure HWIC module accordingly i am unable to
>>>>> >>>> access
>>>>> the
>>>>> >>>> internet my configration pasted below if any experience
>>>>> >>>> person
>>>>> guid me
>>>>> >>>> little.
>>>>> >>>>
>>>>> >>>>
>>>>> >>>> in my phone i just put APN and it work fine without
>>>>> >>>> Authentication *Service provider ask me* that the *username
>>>>> >>>> and password is blank..*
>>>>> >>>>
>>>>> >>>> country Libya
>>>>> >>>> GSM service provider =Almadar APN or access point name
>>>>> >>>> =almadar.net
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>> *Router#show cellular 0/1/0 profile Profile 1 = INACTIVE*
>>>>> >>>> --------
>>>>> >>>> PDP Type = IPv4
>>>>> >>>> Access Point Name (APN) = almadar.net Authentication = None
>>>>> >>>> Username: , Password:
>>>>> >>>>
>>>>> >>>> * - Default profile
>>>>> >>>> *
>>>>> >>>>
>>>>> >>>>
>>>>> ------------------------------------------------------------------
>>>>> --------------------
>>>>> >>>> *Router config*:
>>>>> >>>> *
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> multilink bundle-name authenticated !
>>>>> >>>> chat-script gsm "" "ATDT*99*1#" TIMEOUT 60 "CONNECT"
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> interface Loopback0
>>>>> >>>> ip address 10.0.0.1 255.255.255.0 !
>>>>> >>>> interface Wlan-GigabitEthernet0/0 description Internal
>>>>> >>>> switch interface connecting to the embedded
>>>>> AP
>>>>> >>>> !
>>>>> >>>> interface GigabitEthernet0/0
>>>>> >>>> no ip address
>>>>> >>>> shutdown
>>>>> >>>> duplex auto
>>>>> >>>> speed auto
>>>>> >>>> !
>>>>> >>>> interface wlan-ap0
>>>>> >>>> description Service module interface to manage the embedded
>>>>> >>>> AP no ip address arp timeout 0 no mop enabled no mop
>>>>> >>>> sysid !
>>>>> >>>> interface GigabitEthernet0/1
>>>>> >>>> no ip address
>>>>> >>>> shutdown
>>>>> >>>> duplex auto
>>>>> >>>> speed auto
>>>>> >>>> !
>>>>> >>>> interface ATM0/0/0
>>>>> >>>> no ip address
>>>>> >>>> shutdown
>>>>> >>>> no atm ilmi-keepalive
>>>>> >>>> !
>>>>> >>>> interface Cellular0/1/0
>>>>> >>>> ip address negotiated
>>>>> >>>> encapsulation ppp
>>>>> >>>> dialer in-band
>>>>> >>>> dialer idle-timeout 30
>>>>> >>>> dialer string gsm
>>>>> >>>> dialer-group 1
>>>>> >>>> async mode interactive
>>>>> >>>> ppp ipcp dns request
>>>>> >>>> !
>>>>> >>>> interface Vlan1
>>>>> >>>> no ip address
>>>>> >>>> !
>>>>> >>>> ip forward-protocol nd
>>>>> >>>> !
>>>>> >>>> no ip http server
>>>>> >>>> no ip http secure-server
>>>>> >>>> !
>>>>> >>>> ip route 0.0.0.0 0.0.0.0 Cellular0/1/0 !
>>>>> >>>> access-list 1 permit any
>>>>> >>>> dialer-list 1 protocol ip list 1 !
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> control-plane
>>>>> >>>> !
>>>>> >>>> !
>>>>> >>>> line con 0
>>>>> >>>> line aux 0
>>>>> >>>> line 0/1/0
>>>>> >>>> exec-timeout 0 0
>>>>> >>>> script dialer gsm
>>>>> >>>> login
>>>>> >>>> modem InOut
>>>>> >>>> no exec
>>>>> >>>> speed 80000
>>>>> >>>> line 67
>>>>> >>>> no activation-character
>>>>> >>>> no exec
>>>>> >>>> transport preferred none
>>>>> >>>> transport input all
>>>>> >>>> transport output pad telnet rlogin lapb-ta mop udptn v120
>>>>> >>>> ssh line vty 0 4 login !
>>>>> >>>> scheduler allocate 20000 1000
>>>>> >>>> end*
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>>
>>>>> >>>> kindly Guid me
>>>>> >>>>
>>>>> >>>>
>>>>> >>>> Blogs and organic groups at http://www.ccie.net
>>>>> >>>>
>>>>> >>>>
>>>>> __________________________________________________________________
>>>>> _____
>>>>> >>>> Subscription information may be found at:
>>>>> >>>> http://www.groupstudy.com/list/CCIELab.html
>>>>>
>>>>>
>>>>> Blogs and organic groups at http://www.ccie.net
>>>>>
>>>>> __________________________________________________________________
>>>>> _____ Subscription information may be found at:
>>>>> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Mon Nov 01 2010 - 12:59:59 ART