Re: OT: HWIC-3G-GSM Module Configration Problem...need help

Dear miken:-
i have try your suggestion i it works fine thank you very much

Config part is under cellular interface

 ppp authentication pap chap callin
 ppp chap hostname '
 ppp chap password 0 '
 ppp pap sent-username ' password 0 '

i configured the both method pap and chap

Thanks a lot for your help

On Sun, Oct 31, 2010 at 10:47 AM, muhammad adnan <taurusadnan19_at_gmail.com>wrote:

> Daer thanks for you Reply
> can you more explain your senttence "It required using IPV4 instead of PPP
> with CHAP" how i can configure under my Cellular interface?
>
> i will try to create internet profile with quote mark "
>
> thanks a lot
>
>
>
> On Sun, Oct 31, 2010 at 4:39 AM, miken miken <miken_at_sisna.com> wrote:
>
>> I had a similar issue with a small provider that also expected the
>> username/password to be blank. It required using IPV4 instead of PPP with
>> CHAP and using the quote mark " for the username and password when
>> configuring the cellular profile. TAC recommended using the " . It also did
>> not seem to matter what was configured in the dialer or cellular interface.
>> The actual authentication with the provider appeared to be negotiated using
>> the cellular profile configuration.
>>
>> HTH
>> MikeN
>>
>>
>> On Sat, Oct 30, 2010 at 8:24 AM, muhammad adnan <taurusadnan19_at_gmail.com>wrote:
>>
>>> Dear bilal:- one corection --> did not
>>>
>>> i *didnot* configure the parameter ppp authentication pap or chap
>>> because
>>> if i configure ppp authentication then i must provide username and
>>> password
>>> but service provide ask that the usename and password is blank and i am
>>> accessing the internet over my cell phone without any username or
>>> password
>>>
>>> Thanks a lot
>>> Adnan
>>>
>>>
>>>
>>> On Sat, Oct 30, 2010 at 4:09 PM, muhammad adnan <taurusadnan19_at_gmail.com
>>> >wrote:
>>>
>>> > Dear bilal:-
>>> > i did configure the parameter ppp authentication pap or chap because
>>> if i
>>> > configure ppp authentication then i must provide username and password
>>> but
>>> > service provide ask that the usename and password is blank and i am
>>> > accessing the internet over my cell phone without any username or
>>> password
>>> >
>>> > Thanks a lot
>>> > Adnan
>>> >
>>> >
>>> > On Sat, Oct 30, 2010 at 4:01 PM, Bilal Hansrod <
>>> bilal.hansrod_at_gmail.com>wrote:
>>> >
>>> >> What output do you see when you run below debugs suggested by ERDEM
>>> >>
>>> >> debug chat
>>> >> debug ppp negotiation
>>> >> debug ppp error
>>> >> debug ppp event
>>> >>
>>> >> Regards,
>>> >>
>>> >> Bilal
>>> >>
>>> >>
>>> >> On Sun, Oct 31, 2010 at 12:45 AM, muhammad adnan <
>>> taurusadnan19_at_gmail.com
>>> >> > wrote:
>>> >>
>>> >>> Dear
>>> >>> i am using internet when i placed my sim in my cell phone.if the Data
>>> is
>>> >>> not activated then how i can access.
>>> >>>
>>> >>> Thanks
>>> >>>
>>> >>>
>>> >>>
>>> >>>
>>> >>>
>>> >>> On Sat, Oct 30, 2010 at 3:36 PM, Radioactive Frog <
>>> pbhatkoti_at_gmail.com>wrote:
>>> >>>
>>> >>>> I am not sure if you've already done this but take the SIM card out
>>> from
>>> >>>> the cellular module and put it in your SmartPhone - Sort out the
>>> activation
>>> >>>> isssue first. Make sure data is activated on that SIM.
>>> >>>>
>>> >>>> Then play it once above is confirmed.
>>> >>>>
>>> >>>>
>>> >>>>
>>> >>>> On Sat, Oct 30, 2010 at 11:56 PM, muhammad adnan <
>>> >>>> taurusadnan19_at_gmail.com> wrote:
>>> >>>>
>>> >>>>> Dear Bilal
>>> >>>>> Router#show cellular 0/1/0 all
>>> >>>>> Hardware Information
>>> >>>>> ====================
>>> >>>>> Modem Firmware Version = H1_1_9_3MCAP C:/WS/
>>> >>>>> Modem Firmware built = 12/12/07
>>> >>>>> Hardware Version = 1.0
>>> >>>>> International Mobile Subscriber Identity (IMSI) = 606010105114370
>>> >>>>> International Mobile Equipment Identity (IMEI) = 011359000487907
>>> >>>>> Factory Serial Number (FSN) = D28026013381043
>>> >>>>> Modem Status = Online
>>> >>>>> Current Modem Temperature = 26 deg C, State = Normal
>>> >>>>>
>>> >>>>> Profile Information
>>> >>>>> ====================
>>> >>>>> Profile 1 = INACTIVE*
>>> >>>>> --------
>>> >>>>> PDP Type = IPv4
>>> >>>>> Access Point Name (APN) = almadar.net
>>> >>>>> Authentication = None
>>> >>>>> Username: , Password:
>>> >>>>>
>>> >>>>> * - Default profile
>>> >>>>>
>>> >>>>> Data Connection Information
>>> >>>>> ===========================
>>> >>>>> Data Transmitted = 0 bytes, Received = 0 bytes
>>> >>>>> Profile 1, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 2, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 3, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 4, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 5, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 6, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 7, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 8, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 9, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 10, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 11, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 12, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 13, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 14, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 15, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>> Profile 16, Packet Session Status = INACTIVE
>>> >>>>> Inactivity Reason = Normal inactivate state
>>> >>>>>
>>> >>>>> Network Information
>>> >>>>> ===================
>>> >>>>> Current Service Status = Normal, Service Error = None
>>> >>>>> Current Service = Combined
>>> >>>>> Packet Service = GPRS (Attached)
>>> >>>>> Packet Session Status = Inactive
>>> >>>>> Current Roaming Status = Home
>>> >>>>> Network Selection Mode = Automatic
>>> >>>>> Country = 606, Network = 606 01
>>> >>>>> Mobile Country Code (MCC) = 606
>>> >>>>> Mobile Network Code (MNC) = 1
>>> >>>>> Location Area Code (LAC) = 1
>>> >>>>> Routing Area Code (RAC) = 1
>>> >>>>> Cell ID = 11071
>>> >>>>> Primary Scrambling Code = 0
>>> >>>>> PLMN Selection = Automatic
>>> >>>>> Registered PLMN = Libya Al Madar , Abbreviated = 606 01
>>> >>>>> Service Provider = 606 01
>>> >>>>>
>>> >>>>> Radio Information
>>> >>>>> =================
>>> >>>>> Current Band = GSM 900, Channel Number = 5
>>> >>>>> Current RSSI = -62 dBm
>>> >>>>> Band Selected = Auto
>>> >>>>>
>>> >>>>> Modem Security Information
>>> >>>>> ==========================
>>> >>>>> Card Holder Verification (CHV1) = Disabled
>>> >>>>> SIM Status = OK
>>> >>>>> SIM User Operation Required = None
>>> >>>>> Number of Retries remaining = 3
>>> >>>>>
>>> >>>>>
>>> >>>>> Thanks
>>> >>>>>
>>> >>>>>
>>> >>>>>
>>> >>>>>
>>> >>>>> On Sat, Oct 30, 2010 at 2:42 PM, Bilal Hansrod <
>>> >>>>> bilal.hansrod_at_gmail.com>wrote:
>>> >>>>>
>>> >>>>> > Can you please send the output of *sh cell 0/1/0 all*
>>> >>>>> >
>>> >>>>> >
>>> >>>>> > Bilal
>>> >>>>> >
>>> >>>>> >
>>> >>>>> > On Sat, Oct 30, 2010 at 11:36 PM, muhammad adnan <
>>> >>>>> taurusadnan19_at_gmail.com>wrote:
>>> >>>>> >
>>> >>>>> >> Dear Bilal i configure according to the Cisco Documentation
>>> >>>>> >> and in my mail i pasted show run config...
>>> >>>>> >>
>>> >>>>> >>
>>> >>>>> >>
>>> >>>>> >>
>>> >>>>>
>>> http://www.cisco.com/en/US/docs/routers/access/1800/1861/software/feature/guide/mrwlsgsm.html#wp1040391
>>> >>>>> >>
>>> >>>>> >> in my mail i ask that username and password is blank to access
>>> the
>>> >>>>> >> internet
>>> >>>>> >> Service provider ask me no authentication username and password
>>> >>>>> blank ("i
>>> >>>>> >> just put Apn in my phone and username and password blank and it
>>> >>>>> works fine
>>> >>>>> >> accessing the internet")
>>> >>>>> >>
>>> >>>>> >> if u need any more information kindly let me know again..
>>> >>>>> >>
>>> >>>>> >> Thanks
>>> >>>>> >> Muhammad Adnan
>>> >>>>> >>
>>> >>>>> >>
>>> >>>>> >>
>>> >>>>> >> On Sat, Oct 30, 2010 at 2:28 PM, Bilal Hansrod <
>>> >>>>> bilal.hansrod_at_gmail.com>wrote:
>>> >>>>> >>
>>> >>>>> >>> Hi Muhammad,
>>> >>>>> >>>
>>> >>>>> >>> I can't see a logical interface created for cell interface
>>> where
>>> >>>>> you
>>> >>>>> >>> define your PPP username/password and also the authentication
>>> >>>>> method.
>>> >>>>> >>>
>>> >>>>> >>> An example from my config as below:
>>> >>>>> >>>
>>> >>>>> >>>
>>> >>>>> >>> interface Dialer1
>>> >>>>> >>> ip address negotiated
>>> >>>>> >>> ip virtual-reassembly
>>> >>>>> >>> encapsulation ppp
>>> >>>>> >>> dialer pool 1
>>> >>>>> >>> dialer idle-timeout 0
>>> >>>>> >>> dialer string gsm
>>> >>>>> >>> dialer persistent
>>> >>>>> >>> dialer-group 1
>>> >>>>> >>> no cdp enable
>>> >>>>> >>> ppp authentication chap callin
>>> >>>>> >>> ppp chap hostname XXX
>>> >>>>> >>> ppp chap password YYY
>>> >>>>> >>>
>>> >>>>> >>>
>>> >>>>> >>> Regards,
>>> >>>>> >>>
>>> >>>>> >>> Bilal
>>> >>>>> >>>
>>> >>>>> >>>
>>> >>>>> >>> On Sat, Oct 30, 2010 at 11:05 PM, muhammad adnan <
>>> >>>>> >>> taurusadnan19_at_gmail.com> wrote:
>>> >>>>> >>>
>>> >>>>> >>>> Dear Group members:-
>>> >>>>> >>>> i am trying to configure the
>>> >>>>> 3G-module.i
>>> >>>>> >>>> have inserted my sim card into the HWIC module sim card
>>> properly
>>> >>>>> >>>> working in
>>> >>>>> >>>> the phone and i am accessing the internet.
>>> >>>>> >>>> but when i configure HWIC module accordingly i am unable to
>>> access
>>> >>>>> the
>>> >>>>> >>>> internet my configration pasted below if any experience person
>>> >>>>> guid me
>>> >>>>> >>>> little.
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>> >>>> in my phone i just put APN and it work fine without
>>> Authentication
>>> >>>>> >>>> *Service
>>> >>>>> >>>> provider ask me* that the *username and password is blank..*
>>> >>>>> >>>>
>>> >>>>> >>>> country Libya
>>> >>>>> >>>> GSM service provider =Almadar
>>> >>>>> >>>> APN or access point name =almadar.net
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>> >>>> *Router#show cellular 0/1/0 profile
>>> >>>>> >>>> Profile 1 = INACTIVE*
>>> >>>>> >>>> --------
>>> >>>>> >>>> PDP Type = IPv4
>>> >>>>> >>>> Access Point Name (APN) = almadar.net
>>> >>>>> >>>> Authentication = None
>>> >>>>> >>>> Username: , Password:
>>> >>>>> >>>>
>>> >>>>> >>>> * - Default profile
>>> >>>>> >>>> *
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>>
>>> --------------------------------------------------------------------------------------
>>> >>>>> >>>> *Router config*:
>>> >>>>> >>>> *
>>> >>>>> >>>> !
>>> >>>>> >>>> !
>>> >>>>> >>>> !
>>> >>>>> >>>> multilink bundle-name authenticated
>>> >>>>> >>>> !
>>> >>>>> >>>> chat-script gsm "" "ATDT*99*1#" TIMEOUT 60 "CONNECT"
>>> >>>>> >>>> !
>>> >>>>> >>>> !
>>> >>>>> >>>> !
>>> >>>>> >>>> !
>>> >>>>> >>>> interface Loopback0
>>> >>>>> >>>> ip address 10.0.0.1 255.255.255.0
>>> >>>>> >>>> !
>>> >>>>> >>>> interface Wlan-GigabitEthernet0/0
>>> >>>>> >>>> description Internal switch interface connecting to the
>>> embedded
>>> >>>>> AP
>>> >>>>> >>>> !
>>> >>>>> >>>> interface GigabitEthernet0/0
>>> >>>>> >>>> no ip address
>>> >>>>> >>>> shutdown
>>> >>>>> >>>> duplex auto
>>> >>>>> >>>> speed auto
>>> >>>>> >>>> !
>>> >>>>> >>>> interface wlan-ap0
>>> >>>>> >>>> description Service module interface to manage the embedded
>>> AP
>>> >>>>> >>>> no ip address
>>> >>>>> >>>> arp timeout 0
>>> >>>>> >>>> no mop enabled
>>> >>>>> >>>> no mop sysid
>>> >>>>> >>>> !
>>> >>>>> >>>> interface GigabitEthernet0/1
>>> >>>>> >>>> no ip address
>>> >>>>> >>>> shutdown
>>> >>>>> >>>> duplex auto
>>> >>>>> >>>> speed auto
>>> >>>>> >>>> !
>>> >>>>> >>>> interface ATM0/0/0
>>> >>>>> >>>> no ip address
>>> >>>>> >>>> shutdown
>>> >>>>> >>>> no atm ilmi-keepalive
>>> >>>>> >>>> !
>>> >>>>> >>>> interface Cellular0/1/0
>>> >>>>> >>>> ip address negotiated
>>> >>>>> >>>> encapsulation ppp
>>> >>>>> >>>> dialer in-band
>>> >>>>> >>>> dialer idle-timeout 30
>>> >>>>> >>>> dialer string gsm
>>> >>>>> >>>> dialer-group 1
>>> >>>>> >>>> async mode interactive
>>> >>>>> >>>> ppp ipcp dns request
>>> >>>>> >>>> !
>>> >>>>> >>>> interface Vlan1
>>> >>>>> >>>> no ip address
>>> >>>>> >>>> !
>>> >>>>> >>>> ip forward-protocol nd
>>> >>>>> >>>> !
>>> >>>>> >>>> no ip http server
>>> >>>>> >>>> no ip http secure-server
>>> >>>>> >>>> !
>>> >>>>> >>>> ip route 0.0.0.0 0.0.0.0 Cellular0/1/0
>>> >>>>> >>>> !
>>> >>>>> >>>> access-list 1 permit any
>>> >>>>> >>>> dialer-list 1 protocol ip list 1
>>> >>>>> >>>> !
>>> >>>>> >>>> !
>>> >>>>> >>>> !
>>> >>>>> >>>> control-plane
>>> >>>>> >>>> !
>>> >>>>> >>>> !
>>> >>>>> >>>> line con 0
>>> >>>>> >>>> line aux 0
>>> >>>>> >>>> line 0/1/0
>>> >>>>> >>>> exec-timeout 0 0
>>> >>>>> >>>> script dialer gsm
>>> >>>>> >>>> login
>>> >>>>> >>>> modem InOut
>>> >>>>> >>>> no exec
>>> >>>>> >>>> speed 80000
>>> >>>>> >>>> line 67
>>> >>>>> >>>> no activation-character
>>> >>>>> >>>> no exec
>>> >>>>> >>>> transport preferred none
>>> >>>>> >>>> transport input all
>>> >>>>> >>>> transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
>>> >>>>> >>>> line vty 0 4
>>> >>>>> >>>> login
>>> >>>>> >>>> !
>>> >>>>> >>>> scheduler allocate 20000 1000
>>> >>>>> >>>> end*
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>> >>>> kindly Guid me
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>> >>>> Blogs and organic groups at http://www.ccie.net
>>> >>>>> >>>>
>>> >>>>> >>>>
>>> >>>>>
>>> _______________________________________________________________________
>>> >>>>> >>>> Subscription information may be found at:
>>> >>>>> >>>> http://www.groupstudy.com/list/CCIELab.html
>>> >>>>>
>>> >>>>>
>>> >>>>> Blogs and organic groups at http://www.ccie.net
>>> >>>>>
>>> >>>>>
>>> _______________________________________________________________________
>>> >>>>> Subscription information may be found at:
>>> >>>>> http://www.groupstudy.com/list/CCIELab.html
>>>
>>>
>>> Blogs and organic groups at http://www.ccie.net
>>>
>>> _______________________________________________________________________
>>> Subscription information may be found at:
>>> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Sun Oct 31 2010 - 11:33:33 ART