Re: VOIP: corlist issue ?

You have to apply the corlist on the ephone (or ephone-dn) in order for it
to do anything. The 1st rule of corlist is..
Both the incoming and outgoing dial peer have to have a corlist statement in
order for any cor rule to take effect.

-nick

On Tue, Oct 19, 2010 at 12:05 PM, Carlos G Mendioroz <tron_at_huapi.ba.ar>wrote:

> Well, as the call goes to a DN of a line, the (outgoing) dial-peer
> is implicit (CME). The goal is to do tennant like functionality
> and have phone-1 only see pod-1 dial-peers, and phone-2 only see
> pod-2's.
>
> What I sent was a minimal example config showing the issue.
> Nor inout nor ephone detail show any cor related info.
> :(
>
>
> Ryan West @ 19/10/2010 12:55 -0300 dixit:
>
> Carlos,
>>
>> Usually COR lists are applied outgoing on dial-peers and incoming on DN's.
>> You might try 'debug voip ccapi inout' and 'debug ephone detail' to figure
>> out the issue.
>>
>> -ryan
>>
>> -----Original Message-----
>> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
>> Carlos G Mendioroz
>> Sent: Tuesday, October 19, 2010 11:36 AM
>> To: Cisco certification
>> Subject: VOIP: corlist issue ?
>>
>> Hey there,
>> it might be me, but given this config:
>>
>> ...
>> dial-peer cor custom
>> name Pod-1
>> name Pod-2
>> !
>> !
>> dial-peer cor list Pod-1
>> member Pod-1
>> !
>> dial-peer cor list Pod-2
>> member Pod-2
>>
>> ...
>> ephone-dn 11
>> number 5551000
>> label Local
>> description PSTN-Phone-1
>> corlist incoming Pod-1
>> corlist outgoing Pod-1
>> !
>> !
>> ephone-dn 12
>> number 911
>> label Emergency
>> corlist incoming Pod-1
>> corlist outgoing Pod-1
>> !
>> !
>> ephone-dn 21
>> number 5551000
>> label Local
>> description PSTN-Phone-2
>> corlist incoming Pod-2
>> corlist outgoing Pod-2
>> !
>> !
>> ephone-dn 22
>> number 911
>> label Emergency
>> corlist incoming Pod-2
>> corlist outgoing Pod-2
>> !
>> !
>> ephone 1
>> device-security-mode none
>> description PSTN-Phone-1
>> mac-address 001D.45B5.FF33
>> type 7961
>> button 1:11 2:12
>> !
>> !
>> !
>> ephone 2
>> device-security-mode none
>> description PSTN-Phone-2
>> mac-address 001D.4595.B533
>> type 7961
>> button 1:21 2:22
>> ...
>>
>> If you pick phone-2 line 1 and you dial "911" it should ring phone-2 line
>> 2, ok ? But it rings phone-1.
>>
>> Any known issues with cor lists and CME ?
>> TIA,
>> -Carlos
>>
>>
>> --
>> Carlos G Mendioroz <tron_at_huapi.ba.ar> LW7 EQI Argentina
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>>
> --
> Carlos G Mendioroz <tron_at_huapi.ba.ar> LW7 EQI Argentina
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Tue Oct 19 2010 - 19:14:54 ART