Re: Can't ping

I use "c3725-adventerprisek9-mz.124-15.T14" which works fine.

Thanks.

On Thu, Oct 14, 2010 at 3:04 PM, Jack Router <pan.router_at_gmail.com> wrote:

> What code you use now. I have some weird issues too...
>
> -----Original Message-----
> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> Manouchehr Omari
> Sent: 14-Oct-10 15:02
> To: Ryan DeBerry
> Cc: Cisco certification
> Subject: Re: Can't ping
>
> Thanks Ryan, It works like a champion :)
>
> Regards,
>
>
> On Thu, Oct 14, 2010 at 2:28 PM, Ryan DeBerry <rdeberry_at_gmail.com> wrote:
>
> > Try a newer code I had the same issue with this code.
> >
> >
> > On Thu, Oct 14, 2010 at 2:26 PM, Manouchehr Omari <
> > manouchehr1979_at_gmail.com> wrote:
> >
> >> Dears, Thanks for all the comments, below is the setup,
> >>
> >>
> >> autostart = False
> >> [localhost:7202]
> >> workingdir = working
> >> udp = 20000
> >> [[3725]]
> >> image =
> >> /home/manouchehr/DYNAMIPS/IMAGES/c3725-adventerprisek9-mz.124-15.T10.bin
> >> ram = 256
> >> idlepc = 0x62b22904
> >> ghostios = True
> >> [[ROUTER SW2]]
> >> model = 3725
> >> console = 2008
> >> cnfg = configs/SW2.cfg
> >> slot1 = NM-16ESW
> >> f1/12 = SW3 f1/12
> >>
> >> [[ROUTER SW3]]
> >> model = 3725
> >> console = 2007
> >> cnfg = configs/SW3.cfg
> >> slot1 = NM-16ESW
> >> f1/12 = SW2 f1/12
> >>
> >> ---------------------------------------------
> >>
> >> SW2 - Config
> >>
> >> interface FastEthernet1/12
> >> no switchport
> >> ip address 10.1.2.1 255.255.255.0
> >> end
> >>
> >> router ospf 1
> >> router-id 1.1.1.1
> >> log-adjacency-changes
> >> network 10.1.2.1 0.0.0.0 area 0
> >>
> >>
> >> SW3 - config
> >>
> >> interface FastEthernet1/12
> >> no switchport
> >> ip address 10.1.2.2 255.255.255.0
> >> end
> >>
> >> router ospf 1
> >> router-id 2.2.2.2
> >> log-adjacency-changes
> >> network 10.1.2.2 0.0.0.0 area 0
> >>
> >> ---------------------------------------
> >>
> >> on sw2
> >>
> >> SW2#debug ip icmp
> >> ICMP packet debugging is on
> >> SW2#
> >> SW2#
> >> SW2#ping 10.1.2.2
> >>
> >> Type escape sequence to abort.
> >> Sending 5, 100-byte ICMP Echos to 10.1.2.2, timeout is 2 seconds:
> >> .....
> >> Success rate is 0 percent (0/5)
> >>
> >>
> >> Thanks,
> >>
> >>
> >> On Thu, Oct 14, 2010 at 2:11 PM, --Hammer-- <bhmccie_at_gmail.com> wrote:
> >>
> >> > Enable V2 for RIP.
> >> >
> >> > Just kidding.
> >> >
> >> > Can you give us some more specifics? Configs? Output? Debug IP ICMP?
> >> Etc?
> >> >
> >> > --Hammer
> >> >
> >> > -----Original Message-----
> >> > From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf
> Of
> >> > Manouchehr Omari
> >> > Sent: Thursday, October 14, 2010 12:40 PM
> >> > To: Cisco certification
> >> > Subject: Can't ping
> >> >
> >> > Dears,
> >> >
> >> > I'm facing some weird issue with gns. I have 4 switches directly
> >> connected
> >> > when i start gns and try to ping from one switch to another only the
> >> first
> >> > ping goes but the rest fails, any idea what could be the cause.
> >> >
> >> > P.S. the CPU is not more than 40%.
> >> >
> >> > Thanks in Advance.
> >> >
> >> >
> >> > Blogs and organic groups at http://www.ccie.net
> >> >
> >> >
> _______________________________________________________________________
> >> > Subscription information may be found at:
> >> > http://www.groupstudy.com/list/CCIELab.html
> >>
> >>
> >> Blogs and organic groups at http://www.ccie.net
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Thu Oct 14 2010 - 15:22:21 ART