Re: Ether Channel Query!!

  Thanks Saulat for the quick lab up....

--Hammer--

On 9/27/2010 9:51 AM, Saulat Ali wrote:
> The bundled ports wont show up in the sh spantree command unless you
> type in sh span int<physical port> which will show them in forwarding
> state. As mentioned by Hammer as soon as you put the physical port into
> an ether channel spanning tree process only shows the logical port in
> the sh span tree.
>
> See below e.g .. port 1/0/52 and 2/0/52 wont show up in the span tree
> process but you can view their status by entering sh span<vlan> int gig
> 1/0/52<detail> command,
>
> #sh etherchannel summ
>
> Group Port-channel Protocol Ports
> ------+-------------+-----------+---------------------------------------
> --------
> 1 Po1(SU) LACP Gi1/0/52(P) Gi2/0/52(P)
>
> #sh run int gig 1/0/52
> Building configuration...
>
> Current configuration : 181 bytes
> !
> interface GigabitEthernet1/0/52
> switchport trunk encapsulation dot1q
> switchport mode trunk
> switchport nonegotiate
> channel-group 1 mode active
> end
>
> #sh run int gig 2/0/52
> Building configuration...
>
> Current configuration : 181 bytes
> !
> interface GigabitEthernet2/0/52
> switchport trunk encapsulation dot1q
> switchport mode trunk
> switchport nonegotiate
> channel-group 1 mode active
> end
>
> #sh run int po1
> Building configuration...
>
> Current configuration : 144 bytes
> !
> interface Port-channel1
> switchport trunk encapsulation dot1q
> switchport mode trunk
> switchport nonegotiate
> end
>
>
> #sh span vlan 2
> VLAN0002
> Spanning tree enabled protocol rstp
> Root ID Priority 24578
> Address 0022.be9f.ab80
> This bridge is the root
> Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
>
> Bridge ID Priority 24578 (priority 24576 sys-id-ext 2)
> Address 0022.be9f.ab80
> Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
> Aging Time 300
>
> Interface Role Sts Cost Prio.Nbr Type
> ---------------- ---- --- --------- --------
> --------------------------------
> Po1 Desg FWD 3 128.616 P2p
>
>
> #sh spanning-tree vlan 2 int gi2/0/52 de
> Port 616 (Port-channel1) of VLAN0002 is designated forwarding
> Port path cost 3, Port priority 128, Port Identifier 128.616.
> Designated root has priority 24578, address 0022.be9f.ab80
> Designated bridge has priority 24578, address 0022.be9f.ab80
> Designated port id is 128.616, designated path cost 0
> Timers: message age 0, forward delay 0, hold 0
> Number of transitions to forwarding state: 1
> Link type is point-to-point by default
> BPDU: sent 25045070, received 73
>
> #sh spanning-tree vlan 2 int gig1/0/52 de
> Port 616 (Port-channel1) of VLAN0002 is designated forwarding
> Port path cost 3, Port priority 128, Port Identifier 128.616.
> Designated root has priority 24578, address 0022.be9f.ab80
> Designated bridge has priority 24578, address 0022.be9f.ab80
> Designated port id is 128.616, designated path cost 0
> Timers: message age 0, forward delay 0, hold 0
> Number of transitions to forwarding state: 1
> Link type is point-to-point by default
> BPDU: sent 25045075, received 73
>
> #sh spanning-tree vlan 2 int po1 de
> Port 616 (Port-channel1) of VLAN0002 is designated forwarding
> Port path cost 3, Port priority 128, Port Identifier 128.616.
> Designated root has priority 24578, address 0022.be9f.ab80
> Designated bridge has priority 24578, address 0022.be9f.ab80
> Designated port id is 128.616, designated path cost 0
> Timers: message age 0, forward delay 0, hold 0
> Number of transitions to forwarding state: 1
> Link type is point-to-point by default
> BPDU: sent 25045080, received 73
>
> -----Original Message-----
> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> CCIE KID
> Sent: 27 September 2010 15:29
> To: --Hammer--
> Cc: ccielab_at_groupstudy.com
> Subject: Re: Ether Channel Query!!
>
> Hey can u explain me the process and what r the packets exchanged so
> that
> how does STP come to know that that the particular port is bundled
>
> What will be in the sh spanning-tree detail for that particular port
> which
> is been blocking
> Whether it will be of forwarding state
>
> That bundled link will be in which state in forwarding state in STP ah??
> pls brief me about that??
>
> On Mon, Sep 27, 2010 at 7:51 PM, --Hammer--<bhmccie_at_gmail.com> wrote:
>
>> CCIE KID,
>> When you "bond" the two physical interfaces into a logical port
> channel,
>> you will pass traffic over both Fa0/1 and Fa0/2. STP treats the entire
>> collection of physical interfaces as a single logical port. This is
> all
>> negotiated between the endpoints. Does that help?
>>
>> --Hammer--
>>
>>
>>
>> On 9/27/2010 9:17 AM, CCIE KID wrote:
>>
>>> I have a doubt in ether Channel
>>>
>>> This is my scenario
>>>
>>> SW1 fa0/1-------------------------------------------fa 0/1 SW2
>>> fa0/2-------------------------------------------fa 0/2
>>>
>>> In STP SW1 is the root bridge and SW2 is the non root bridge , In SW2
> fa
>>> 0/1
>>> is in forwarding state and fa 0/2 is in blocking state .
>>> So in Ether channel, if we bundle fa0/1 and fa 0/2 ,traffic cannot be
>>> passed
>>> through fa 0/2 .
>>> How Ether Channel informs STP about the bundling and makes the fa 0/2
> into
>>> forwarding
>>> Can anyone explain me the process
>>> I am expecting the experts to explain
>>>
>>>
>>>
>>> With Warmest Regards,
>>>
>>> CCIE KID
>>> IN PURSUIT OF CCIE
>>>
>>>
>>> Blogs and organic groups at http://www.ccie.net
>>>
>>>
> _______________________________________________________________________
>>> Subscription information may be found at:
>>> http://www.groupstudy.com/list/CCIELab.html
>>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>>
> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Mon Sep 27 2010 - 10:09:08 ART