Re: etherchannel problem

Hi tyson
In the remote site there is the same config and the same
hardware&ios.but in the remote protofol field is empty.is there any
spesific reason for that

2010/8/31, Tyson Scott <tscott_at_ipexpert.com>:
> It all depends on the system. Some will some won't. If you hardcode the
> etherchannel to on and put a port analyzer between there you will still see
> PaGP frames traversing the link. Test it out.
>
> Regards,
>
> Tyson Scott - CCIE #13513 R&S, Security, and SP
> Managing Partner / Sr. Instructor - IPexpert, Inc.
> Mailto: tscott_at_ipexpert.com
>
>
>
> -----Original Message-----
> From: GAURAV MADAN [mailto:gauravmadan1177_at_gmail.com]
> Sent: Tuesday, August 31, 2010 1:40 PM
> To: Tyson Scott
> Cc: Mustafa Yadav; Cisco certification
> Subject: Re: etherchannel problem
>
> I dont see such a problem in my switch .. How is this Normal ?
>
> Gaurav Madan
>
> On Tue, Aug 31, 2010 at 9:54 PM, Tyson Scott <tscott_at_ipexpert.com> wrote:
>> That is not a bug or a problem. That is normal.
>>
>> Regards,
>>
>> Tyson Scott - CCIE #13513 R&S, Security, and SP
>> Managing Partner / Sr. Instructor - IPexpert, Inc.
>> Mailto: tscott_at_ipexpert.com
>>
>>
>>
>> -----Original Message-----
>> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
>> Mustafa Yadav
>> Sent: Tuesday, August 31, 2010 12:12 PM
>> To: Cisco certification
>> Subject: etherchannel problem
>>
>> Hi Guys,
>>
>>
>> As you see below even channel group configured as mode on it is shown
> as
>> protocol pagp.What would be root cause for this?
>>
>>
>> sh run int g1/23
>> Building configuration...
>>
>> Current configuration : 722 bytes
>> !
>> interface GigabitEthernet1/23
>> switchport
>> switchport trunk encapsulation dot1q
>> switchport mode trunk
>> carrier-delay msec 0
>> mls qos trust dscp
>> spanning-tree link-type point-to-point
>> channel-group 2 mode on
>> end
>>
>> sh etherchannel summary
>> Flags: D - down P - bundled in port-channel
>> I - stand-alone s - suspended
>> H - Hot-standby (LACP only)
>> R - Layer3 S - Layer2
>> U - in use f - failed to allocate aggregator
>>
>> M - not in use, minimum links not met
>> u - unsuitable for bundling
>> w - waiting to be aggregated
>> d - default port
>>
>>
>> Number of channel-groups in use: 1
>> Number of aggregators: 1
>>
>> Group Port-channel Protocol Ports
>>
> ------+-------------+-----------+-------------------------------------------
>> ----
>> 2 Po2(SU) PAgP Gi1/23(P)
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>>
>
>

-- 
Mobil cihaz}mdan gvnderildi
Blogs and organic groups at http://www.ccie.net