Re: Unable to bring up the trunk

Get a crossover cable - both interfaces are down/down.

On Fri, Aug 27, 2010 at 12:59 AM, Naufal Jamal <naufalccie_at_yahoo.in> wrote:
> PFA... Let me know if you need any other outputs...
>
> --- On Fri, 27/8/10, Yandy Ramirez <yandyr_at_gmail.com> wrote:
>
> From: Yandy Ramirez <yandyr_at_gmail.com>
> Subject: Re: Unable to bring up the trunk
> To: "Kambiz Agahian" <aussiecert_at_gmail.com>
> Cc: "Naufal Jamal" <naufalccie_at_yahoo.in>, ccielab_at_groupstudy.com
> Date: Friday, 27 August, 2010, 4:40 AM
>
> Same here, can't make anything out..
>
> ------
> yandy
>
>
> On Fri, Aug 27, 2010 at 00:19, Kambiz Agahian <aussiecert_at_gmail.com> wrote:
>
>
> Naufal,
>
>
> I'm not sure about the other guys but I can't really read this distorted
>
> config. Could you please always send your config as a small attachment?
>
>
> Kambiz Agahian
>
>
> CCIE Instructor/Consultant
>
> M.Eng Telecom, CCIE# 25341, CCSI# 33326, MCSE, MCSA
>
>
>
> On Thu, Aug 26, 2010 at 9:05 PM, Naufal Jamal <naufalccie_at_yahoo.in> wrote:
>
>
>> Hi Guys,
>
>> I am pretty amused on this. I am just trying to bring up the trunk between
>
>> two
>
>> switches i am unable to find a good reason for that not to come up...
>
>> I am using two 2924C-XL-EN switches and connected them through their f0/1
>
>> interface. I am trying to bring up the trunk between them..but dont know
>
>> why
>
>> it is not coming up..theport works fine as access port.. Please help..
>
>> Switch A:
>
>> SW2#sh run int f0/1Building configuration...
>
>> Current configuration:!interface FastEthernet0/1 duplex full speed
>
>> 100 switchport trunk allowed vlan 1,10,1002-1005 switchport mode trunkend
>
>> SW2#sh int f0/1 switchportName: Fa0/1Switchport: EnabledAdministrative
>
>> mode:
>
>> trunkOperational Mode: trunkAdministrative Trunking Encapsulation:
>
>> islOperational Trunking Encapsulation: islNegotiation of Trunking:
>
>> DisabledAccess Mode VLAN: 0 ((Inactive))Trunking Native Mode VLAN: 1
>
>> (default)Trunking VLANs Enabled: 1,10,1002-1005Trunking VLANs Active:
>
>> 1,10Pruning VLANs Enabled: 2-1001
>
>> Priority for untagged frames: 0Override vlan tag priority: FALSEVoice
> VLAN:
>
>> noneAppliance trust: noneSelf Loopback: NoSW2#sh int f0/1FastEthernet0/1
> is
>
>> down, line protocol is down Hardware is Fast Ethernet, address is
>
>> 0004.c1c0.65c1 (bia 0004.c1c0.65c1) MTU 1500 bytes, BW 100000 Kbit, DLY
>
>> 100
>
>> usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation
>
>> ARPA,
>
>> loopback not set Keepalive not set Full-duplex, 100Mb/s, 100BaseTX/FX
>
>> ARP
>
>> type: ARPA, ARP Timeout 04:00:00 Last input never, output 01:21:46,
> output
>
>> hang never Last clearing of "show interface" counters never Queueing
>
>> strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5
>
>> minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0
>
>> bits/sec,
>
>> 0 packets/sec 1 packets input, 64 bytes Received 0 broadcasts, 0
>
>> runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0
> overrun,
>
>> 0
>
>> ignored 0 watchdog, 0
>
>> multicast 0 input packets with dribble condition detected 3
>
>> packets
>
>> output, 858 bytes, 0 underruns 0 output errors, 0 collisions, 5
>
>> interface
>
>> resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0
> no
>
>> carrier 0 output buffer failures, 0 output buffers swapped
>
>>
> out------------------------------------------------------------------------
>
>> Switch B:
>
>> Current configuration:!interface FastEthernet0/1 duplex full speed
>
>> 100 switchport trunk allowed vlan 1,10,1002-1005 switchport mode trunkend
>
>> SW1#sh int f0/1 switchName: Fa0/1Switchport: EnabledAdministrative mode:
>
>> trunkOperational Mode: trunkAdministrative Trunking Encapsulation:
>
>> islOperational Trunking Encapsulation: islNegotiation of Trunking:
>
>> DisabledAccess Mode VLAN: 0 ((Inactive))Trunking Native Mode VLAN: 1
>
>> (default)Trunking VLANs Enabled: 1,10,1002-1005Trunking VLANs Active:
>
>> 1Pruning
>
>> VLANs Enabled: 2-1001
>
>> Priority for untagged frames: 0Override vlan tag priority: FALSEVoice
> VLAN:
>
>> noneAppliance trust: noneSelf Loopback: NoSW1#sh int f0/1FastEthernet0/1
> is
>
>> down, line protocol is down Hardware is Fast Ethernet, address is
>
>> 00b0.64a4.d9c1 (bia 00b0.64a4.d9c1) MTU 1500 bytes, BW 100000 Kbit, DLY
>
>> 100
>
>> usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation
>
>> ARPA,
>
>> loopback not set Keepalive not set Full-duplex, 100Mb/s, 100BaseTX/FX
>
>> ARP
>
>> type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:50:22,
> output
>
>> hang never Last clearing of "show interface" counters never Queueing
>
>> strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5
>
>> minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0
>
>> bits/sec,
>
>> 0 packets/sec 5 packets input, 971 bytes Received 4 broadcasts, 0
>
>> runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0
> overrun,
>
>> 0
>
>> ignored 0 watchdog, 0
>
>> multicast 0 input packets with dribble condition detected 133
>
>> packets
>
>> output, 12998 bytes, 0 underruns 0 output errors, 0 collisions, 5
>
>> interface resets 0 babbles, 0 late collision, 0 deferred 0 lost
>
>> carrier, 0 no carrier--------------
>
>> I have tried IOS upgrade, speed/duplex setting change, cable change etc
> but
>
>> dont knw why the trunk is not coming up....the port works fine when it is
>
>> used
>
>> as access port.
>
>> Any idea how 2924 switches trunk behaves??
>
>>
>
>>
>
>> Blogs and organic groups at http://www.ccie.net
>
>>
>
>> _______________________________________________________________________
>
>> Subscription information may be found at:
>
>> http://www.groupstudy.com/list/CCIELab.html
>
>
>
> Blogs and organic groups at http://www.ccie.net
>
>
> _______________________________________________________________________
>
> Subscription information may be found at:
>
> http://www.groupstudy.com/list/CCIELab.html
> Switch A:
>
> SW1#sh run int f0/1
> Building configuration...
>
> Current configuration:
> !
> interface FastEthernet0/1
> switchport mode trunk
> end
>
> SW1#sh int f0/1 switchport
> Name: Fa0/1
> Switchport: Enabled
> Administrative mode: trunk
> Operational Mode: trunk
> Administrative Trunking Encapsulation: isl
> Operational Trunking Encapsulation: isl
> Negotiation of Trunking: Disabled
> Access Mode VLAN: 0 ((Inactive))
> Trunking Native Mode VLAN: 1 (default)
> Trunking VLANs Enabled: ALL
> Trunking VLANs Active: 1
> Pruning VLANs Enabled: 2-1001
>
> Priority for untagged frames: 0
> Override vlan tag priority: FALSE
> Voice VLAN: none
> Appliance trust: none
> Self Loopback: No
>
>
> SW1#sh int f0/1
> FastEthernet0/1 is down, line protocol is down
> Hardware is Fast Ethernet, address is 00b0.64a4.d9c1 (bia 00b0.64a4.d9c1)
> MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation ARPA, loopback not set
> Keepalive not set
> Auto-duplex , Auto Speed , 100BaseTX/FX
> ARP type: ARPA, ARP Timeout 04:00:00
> Last input never, output 00:27:19, output hang never
> Last clearing of "show interface" counters never
> Queueing strategy: fifo
> Output queue 0/40, 0 drops; input queue 0/75, 0 drops
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 5 packets input, 971 bytes
> Received 4 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
> 0 watchdog, 0 multicast
> 0 input packets with dribble condition detected
> 181 packets output, 16386 bytes, 0 underruns
> 0 output errors, 0 collisions, 5 interface resets
> 0 babbles, 0 late collision, 0 deferred
> 0 lost carrier, 0 no carrier
> 0 output buffer failures, 0 output buffers swapped out
> SW1#
> -----------------------------------------------------------------------------
>
> Switch B:
>
> SW2#sh run int f0/1
> Building configuration...
>
> Current configuration:
> !
> interface FastEthernet0/1
> switchport mode trunk
> end
>
> SW2#sh int f0/1 switchpor
> Name: Fa0/1
> Switchport: Enabled
> Administrative mode: trunk
> Operational Mode: trunk
> Administrative Trunking Encapsulation: isl
> Operational Trunking Encapsulation: isl
> Negotiation of Trunking: Disabled
> Access Mode VLAN: 0 ((Inactive))
> Trunking Native Mode VLAN: 1 (default)
> Trunking VLANs Enabled: ALL
> Trunking VLANs Active: 1,10,20,30,40
> Pruning VLANs Enabled: 2-1001
>
> Priority for untagged frames: 0
> Override vlan tag priority: FALSE
> Voice VLAN: none
> Appliance trust: none
> Self Loopback: No
>
>
> SW2#sh int f0/1
> FastEthernet0/1 is down, line protocol is down
> Hardware is Fast Ethernet, address is 0004.c1c0.65c1 (bia 0004.c1c0.65c1)
> MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation ARPA, loopback not set
> Keepalive not set
> Auto-duplex , Auto Speed , 100BaseTX/FX
> ARP type: ARPA, ARP Timeout 04:00:00
> Last input never, output 00:12:29, output hang never
> Last clearing of "show interface" counters never
> Queueing strategy: fifo
> Output queue 0/40, 0 drops; input queue 0/75, 0 drops
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 1 packets input, 64 bytes
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
> 0 watchdog, 0 multicast
> 0 input packets with dribble condition detected
> 28 packets output, 4134 bytes, 0 underruns
> 0 output errors, 0 collisions, 5 interface resets
> 0 babbles, 0 late collision, 0 deferred
> 0 lost carrier, 0 no carrier
> 0 output buffer failures, 0 output buffers swapped out
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Fri Aug 27 2010 - 01:20:26 ART