RE: Copy via Http

No clue on that one. Could be high CPU on the PC not being able to give CPU
time to the process. Keepalive is 10 seconds by default, what happens if you
disable keepalives on both ends. Do you have 2 routers with a 3rd acting as
a frame switch. Could be any of the three checking out for too long.

David

--
http://dcp.dcptech.com
> -----Original Message-----
> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> Bilal Hansrod
> Sent: Monday, August 23, 2010 10:37 PM
> To: David Prall
> Cc: Stephen Amaki; ccielab_at_groupstudy.com
> Subject: Re: Copy via Http
> 
> David,
> 
> It looks like the frame sub interface that has PVC to R5 goes down
> after I
> copy via http. Could this be related to GNS3.
> 
> Regards,
> 
> Bilal
> 
> On Tue, Aug 24, 2010 at 5:34 AM, David Prall <dcp_at_dcptech.com> wrote:
> 
> > On the failure example, it shows an interface coming up. When this
> happens
> > is the routing table to the source changing?
> >
> > --
> > http://dcp.dcptech.com
> >
> >
> > > -----Original Message-----
> > > From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On
> Behalf Of
> > > Bilal Hansrod
> > > Sent: Monday, August 23, 2010 3:14 PM
> > > To: Stephen Amaki
> > > Cc: David Prall; <ccielab_at_groupstudy.com>
> > > Subject: Re: Copy via Http
> > >
> > > I apologise that i should have clarified. Im running hypervisor
> > > ( GNS3) for routers and 4 physical 3550 switch. As per Davids
> > > suggestion , im able to get few successful Transfer and them get
> > > bromen pipe error
> > >
> > > Thanks & Regards,
> > > Bilal Hansrod
> > >
> > > Sent from my iPhone
> > >
> > >
> > > On 23/08/2010, at 11:24 PM, Stephen Amaki <swamaki_at_gmail.com>
> wrote:
> > >
> > > > Oh wait, are you running some type of hardware as in 3550/3560?
> If
> > > > not, it is not possible the image c3550-ipservicesk9-mz.
> > > > 122-44.SE2.bin is in the flash unless you dumped it in there.
> > > > Dynamips is virtual.
> > > >
> > > > Do a "sh flash:" If you dont see c3550-ipservicesk9-mz.
> > > > 122-44.SE2.bin, you cannot copy it. Think about it, you're
> copying a
> > > > file that does not exist.
> > > >
> > > > Steve.
> > > >
> > > >
> > > > On Mon, Aug 23, 2010 at 8:59 AM, Bilal Hansrod
> > > <bilal.hansrod_at_gmail.com
> > > > > wrote:
> > > > Stephen,
> > > >
> > > > I wanted to pull config from SW2 back to R4. i was just wondering
> > > > how is below example helps my task. Any suggestions!
> > > >
> > > > Regards,
> > > >
> > > > Bilal
> > > >
> > > >
> > > >
> > > > On Mon, Aug 23, 2010 at 11:02 AM, Stephen Amaki
> <swamaki_at_gmail.com>
> > > > wrote:
> > > > Hi Bilal,
> > > >
> > > > Dynamips/dynagen/gns3 will not store the ios image in the flash.
> The
> > > > workaround this if you are looking to generate some http traffic
> is
> > > > to create an exception dump in the flash.
> > > >
> > > > You can then do a :  copy http://cisco:cisco@150.1.6.6/R6-core.Z
> > > null:
> > > >
> > > > HTH
> > > > here's what you do:
> > > >
> > > > 1. Increase flash size for particular device in the GNS3
> > > > (= right click on the device-> configure-> Memories and disks - >
> > > > PCMCIA disk0 size: 99MB)
> > > >
> > > > 2. Use flash for Core Dumps:
> > > >    R6(config)#exception flash all flash:
> > > >
> > > > 3. R6#reload
> > > >
> > > >    [confirm] yes
> > > >    Wait until process for core dump is finished and you just see
> > > > something like below constantly repeated in your terminal:
> > > >
> > > >    %ALIGN-1-FATAL: Corrupted program......
> > > >
> > > > 4."Stop" the device in GNS3 and then "Start"
> > > >
> > > > 5.R6#show flash:
> > > >
> > > > System CompactFlash directory:
> > > > File   Length   Name/status
> > > >   1    151350   crashinfo_20020301-000729
> > > >   2    50640    R6-coreiomen.Z
> > > >   3    64737571 R6-core.Z
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > On Sun, Aug 22, 2010 at 8:05 PM, Bilal Hansrod
> > > <bilal.hansrod_at_gmail.com
> > > > > wrote:
> > > > Thanks David, i will try and let you know.
> > > >
> > > >
> > > > Thanks & Regards,
> > > > Bilal Hansrod
> > > >
> > > > Sent from my iPhone
> > > >
> > > >
> > > > On 23/08/2010, at 8:42 AM, "David Prall" <dcp_at_dcptech.com> wrote:
> > > >
> > > > What happens if you do:
> > > > copy http://150.1.8.8/c3550-ipservicesk9-mz.122-44.SE2.bin null:
> > > >
> > > > From the prompts it is putting 150.1.8.8 as both the server and
> part
> > > > of the
> > > > filename.
> > > >
> > > > David
> > > >
> > > > --
> > > > http://dcp.dcptech.com
> > > >
> > > >
> > > > -----Original Message-----
> > > > From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On
> Behalf
> > > > Of
> > > > Bilal Hansrod
> > > > Sent: Sunday, August 22, 2010 6:31 PM
> > > > To: ccielab_at_groupstudy.com
> > > > Subject: Fwd: Copy via Http
> > > >
> > > > Any expert advise? Thanks in advance
> > > >
> > > > Thanks & Regards,
> > > > Bilal Hansrod
> > > >
> > > > Sent from my iPhone
> > > >
> > > >
> > > > Begin forwarded message:
> > > >
> > > > From: Bilal Hansrod <bilal.hansrod_at_gmail.com>
> > > > Date: 23 August 2010 1:21:51 AM AEST
> > > > To: Cisco certification <ccielab_at_groupstudy.com>
> > > > Subject: Copy via Http
> > > >
> > > >
> > > > Hello Guys,
> > > >
> > > > I am trying to copy a file from switch using http protocol. I am
> > > > using GNS3 and was working on INE Workbook 1, task 3.15 (PfR)
> > > >
> > > > The configuration done on router as below:
> > > >
> > > > no ip http server
> > > > no ip http secure-server
> > > > ip http client source-interface Loopback0
> > > > ip http client username cisco
> > > > ip http client password 0 cisco
> > > >
> > > >
> > > > The switch configuration as below:
> > > >
> > > > ip http server
> > > > no ip http secure-server
> > > > ip http path flash:
> > > >
> > > >
> > > > The command running on router as below:
> > > > copy http:150.1.8.8/c3550-ipservicesk9-mz.122-44.SE2.bin null:
> > > >
> > > > Unfortunately, I am getting error as below:
> > > >
> > > > Address or name of remote host [150.1.8.8]?
> > > > Source filename [150.1.8.8/c3550-ipservicesk9-mz.122-44.SE2.bin]?
> > > > %Error opening http://150.1.8.8/150.1.8.8/c3550-ipservicesk9-
> mz.122-
> > > > 44.SE2.bin
> > > > (No such file or directory)
> > > >
> > > >
> > > > Any help would be highly appreciated!
> > > >
> > > > Regards,
> > > >
> > > > Bilal
> > > >
> > > >
> > > > Blogs and organic groups at http://www.ccie.net
> > > >
> > > >
> > >
> _______________________________________________________________________
> > >
> > >
> > > >
> > > >
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> > > >
> > > >
> > > > Blogs and organic groups at http://www.ccie.net
> > > >
> > > >
> > >
> _______________________________________________________________________
> > >
> > >
> > > > Subscription information may be found
> at:http://www.groupstudy.com/
> > > > list/CCIELab.html
> > >
> > >
> > > Blogs and organic groups at http://www.ccie.net
> > >
> > >
> _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> 
> 
> Blogs and organic groups at http://www.ccie.net
> 
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net