RE: Copy via Http

On the failure example, it shows an interface coming up. When this happens
is the routing table to the source changing?

--
http://dcp.dcptech.com
> -----Original Message-----
> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> Bilal Hansrod
> Sent: Monday, August 23, 2010 3:14 PM
> To: Stephen Amaki
> Cc: David Prall; <ccielab_at_groupstudy.com>
> Subject: Re: Copy via Http
> 
> I apologise that i should have clarified. Im running hypervisor
> ( GNS3) for routers and 4 physical 3550 switch. As per Davids
> suggestion , im able to get few successful Transfer and them get
> bromen pipe error
> 
> Thanks & Regards,
> Bilal Hansrod
> 
> Sent from my iPhone
> 
> 
> On 23/08/2010, at 11:24 PM, Stephen Amaki <swamaki_at_gmail.com> wrote:
> 
> > Oh wait, are you running some type of hardware as in 3550/3560? If
> > not, it is not possible the image c3550-ipservicesk9-mz.
> > 122-44.SE2.bin is in the flash unless you dumped it in there.
> > Dynamips is virtual.
> >
> > Do a "sh flash:" If you dont see c3550-ipservicesk9-mz.
> > 122-44.SE2.bin, you cannot copy it. Think about it, you're copying a
> > file that does not exist.
> >
> > Steve.
> >
> >
> > On Mon, Aug 23, 2010 at 8:59 AM, Bilal Hansrod
> <bilal.hansrod_at_gmail.com
> > > wrote:
> > Stephen,
> >
> > I wanted to pull config from SW2 back to R4. i was just wondering
> > how is below example helps my task. Any suggestions!
> >
> > Regards,
> >
> > Bilal
> >
> >
> >
> > On Mon, Aug 23, 2010 at 11:02 AM, Stephen Amaki <swamaki_at_gmail.com>
> > wrote:
> > Hi Bilal,
> >
> > Dynamips/dynagen/gns3 will not store the ios image in the flash. The
> > workaround this if you are looking to generate some http traffic is
> > to create an exception dump in the flash.
> >
> > You can then do a :  copy http://cisco:cisco@150.1.6.6/R6-core.Z
> null:
> >
> > HTH
> > here's what you do:
> >
> > 1. Increase flash size for particular device in the GNS3
> > (= right click on the device-> configure-> Memories and disks - >
> > PCMCIA disk0 size: 99MB)
> >
> > 2. Use flash for Core Dumps:
> >    R6(config)#exception flash all flash:
> >
> > 3. R6#reload
> >
> >    [confirm] yes
> >    Wait until process for core dump is finished and you just see
> > something like below constantly repeated in your terminal:
> >
> >    %ALIGN-1-FATAL: Corrupted program......
> >
> > 4."Stop" the device in GNS3 and then "Start"
> >
> > 5.R6#show flash:
> >
> > System CompactFlash directory:
> > File   Length   Name/status
> >   1    151350   crashinfo_20020301-000729
> >   2    50640    R6-coreiomen.Z
> >   3    64737571 R6-core.Z
> >
> >
> >
> >
> >
> > On Sun, Aug 22, 2010 at 8:05 PM, Bilal Hansrod
> <bilal.hansrod_at_gmail.com
> > > wrote:
> > Thanks David, i will try and let you know.
> >
> >
> > Thanks & Regards,
> > Bilal Hansrod
> >
> > Sent from my iPhone
> >
> >
> > On 23/08/2010, at 8:42 AM, "David Prall" <dcp_at_dcptech.com> wrote:
> >
> > What happens if you do:
> > copy http://150.1.8.8/c3550-ipservicesk9-mz.122-44.SE2.bin null:
> >
> > From the prompts it is putting 150.1.8.8 as both the server and part
> > of the
> > filename.
> >
> > David
> >
> > --
> > http://dcp.dcptech.com
> >
> >
> > -----Original Message-----
> > From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf
> > Of
> > Bilal Hansrod
> > Sent: Sunday, August 22, 2010 6:31 PM
> > To: ccielab_at_groupstudy.com
> > Subject: Fwd: Copy via Http
> >
> > Any expert advise? Thanks in advance
> >
> > Thanks & Regards,
> > Bilal Hansrod
> >
> > Sent from my iPhone
> >
> >
> > Begin forwarded message:
> >
> > From: Bilal Hansrod <bilal.hansrod_at_gmail.com>
> > Date: 23 August 2010 1:21:51 AM AEST
> > To: Cisco certification <ccielab_at_groupstudy.com>
> > Subject: Copy via Http
> >
> >
> > Hello Guys,
> >
> > I am trying to copy a file from switch using http protocol. I am
> > using GNS3 and was working on INE Workbook 1, task 3.15 (PfR)
> >
> > The configuration done on router as below:
> >
> > no ip http server
> > no ip http secure-server
> > ip http client source-interface Loopback0
> > ip http client username cisco
> > ip http client password 0 cisco
> >
> >
> > The switch configuration as below:
> >
> > ip http server
> > no ip http secure-server
> > ip http path flash:
> >
> >
> > The command running on router as below:
> > copy http:150.1.8.8/c3550-ipservicesk9-mz.122-44.SE2.bin null:
> >
> > Unfortunately, I am getting error as below:
> >
> > Address or name of remote host [150.1.8.8]?
> > Source filename [150.1.8.8/c3550-ipservicesk9-mz.122-44.SE2.bin]?
> > %Error opening http://150.1.8.8/150.1.8.8/c3550-ipservicesk9-mz.122-
> > 44.SE2.bin
> > (No such file or directory)
> >
> >
> > Any help would be highly appreciated!
> >
> > Regards,
> >
> > Bilal
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> >
> _______________________________________________________________________
> 
> 
> >
> >
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> >
> _______________________________________________________________________
> 
> 
> > Subscription information may be found at:http://www.groupstudy.com/
> > list/CCIELab.html
> 
> 
> Blogs and organic groups at http://www.ccie.net
> 
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net